航空齿轮钢C69高温渗碳后的组织性能

doi:10.13251/j.issn.0254-6051.2022.04.038

金属热处理 ›› 2022, Vol. 47 ›› Issue (4): 219-225.DOI: 10.13251/j.issn.0254-6051.2022.04.038

航空齿轮钢C69高温渗碳后的组织性能

戴建科¹, 韩顺¹, 厉勇¹, 刘宪民¹, 王春旭¹, 庞学东², 李建新²

1.钢铁研究总院有限公司特殊钢研究院, 北京 100081;
2.抚顺特殊钢股份有限公司技术中心, 辽宁抚顺 113001

收稿日期:2022-01-16 修回日期:2022-02-09 出版日期:2022-04-25 发布日期:2022-05-19
通讯作者: 韩顺, 高级工程师,E-mail:hanshunfa@126.com
作者简介:戴建科(1997—),男,硕士研究生,主要研究方向为超高强度钢,E-mail: dai_jianke@ 163.com。

Microstructure and properties of C69 gear steel for aviation after high temperature carburizing

Dai Jianke¹, Han Shun¹, Li Yong¹, Liu Xianmin¹, Wang Chunxu¹, Pang Xuedong², Li Jianxin²

1. Research Institute of Special Steels, Central Iron and Steel Research Institute Co., Ltd., Beijing 100081, China;
2. Technology Center, Fushun Special Steel Co., Ltd., Fushun Liaoning 113001, China

Received:2022-01-16 Revised:2022-02-09 Online:2022-04-25 Published:2022-05-19

摘要/Abstract

摘要： 通过OM、SEM、TEM以及显微硬度计等设备研究了1050 ℃下不同渗碳工艺对航空齿轮钢C69组织及性能的影响。结果表明,经渗碳、深冷和回火处理后,渗碳层表层的显微硬度最高可达约950 HV0.3,组织为针状马氏体,马氏体上观察到M₃C、M₂C碳化物,晶界处有M₇C₃碳化物分布,次表层组织为针状马氏体和板条马氏体,心部显微硬度约为630 HV0.3,组织主要为板条马氏体。循环渗碳的渗碳效率更高,随循环次数增加,试验钢的表面碳含量和渗碳层深度不断提高,且晶界处M₇C₃尺寸和数量逐渐增加。4次循环渗碳的表面碳含量为1.14%,渗碳层深度约为3.0 mm。

关键词: 航空齿轮钢, C69钢, 渗碳工艺, 渗层硬度, 碳化物

Abstract: Effect of different carburizing processes at 1050 ℃ on microstructure and properties of gear steel C69 for aviation was studied by using OM, SEM, TEM and Vickers hardness tester. The results show that after carburizing, cryogenic and tempering, the surface hardness of the carburized layer can reach about 950 HV0.3, and the microstructure is acicular martensite where the M₃C and M₂C carbides precipitate, and the M₇C₃carbides precipitate at grain boundary. At the sub-layer of the carburized surface, microstructure is composed of acicular martensite and lath martensite. At the core, the microstructure is lath martensite and the hardness is about 630 HV0.3. The cyclic carburizing has higher carburizing efficiency. With the increase of carburizing cycle, the thickness of carburized layer and surface carbon concentration increase continuously, and the size and quantity of the M₇C₃ at the grain boundary also increase. After four cycles carburizing, the surface carbon concentration is 1.14%, and the thickness of carburized layer is about 3.0 mm.

Key words: aviation gear steel, C69 steel, carburizing process, carburized layer hardness, carbide

中图分类号:

TG142.1

戴建科, 韩顺, 厉勇, 刘宪民, 王春旭, 庞学东, 李建新. 航空齿轮钢C69高温渗碳后的组织性能[J]. 金属热处理, 2022, 47(4): 219-225.

Dai Jianke, Han Shun, Li Yong, Liu Xianmin, Wang Chunxu, Pang Xuedong, Li Jianxin. Microstructure and properties of C69 gear steel for aviation after high temperature carburizing[J]. Heat Treatment of Metals, 2022, 47(4): 219-225.

参考文献

[1]杨延辉, 王毛球, 陈敬超, 等. 高温渗碳齿轮钢的研究进展[J]. 特殊钢, 2013, 34(1): 22-24.
Yang Yanhui, Wang Maoqiu, Chen Jingchao, et al. Research progress in gear steels for high temperature carburization[J]. Special Steel, 2013, 34(1): 22-24.
[2]Yang Yanhui, Wang Maoqiu, Chen Jingchao, et al. Microstructure and mechanical properties of gear steels after high temperature carburization[J]. Journal of Iron and Steel Research, International, 2013, 20(12): 140-145.
[3]赵文军, 刘国强, 王金栋, 等. 20Cr2Ni4A齿轮钢高温渗碳工艺[J]. 金属热处理, 2015, 40(12): 142-145.
Zhao Wenjun, Liu Guoqiang, Wang Jindong, et al. High temperature carburizing process of 20Cr2Ni4A gear steel[J]. Heat Treatment of Metals, 2015, 40(12): 142-145.
[4]田勇, 安小雪, 王昭东, 等. 12Cr2Ni4A钢高温真空低压脉冲渗碳工艺[J]. 东北大学学报(自然科学版), 2020, 41(9): 1251-1256.
Tian Yong, An Xiaoxue, Wang Zhaodong, et al. High temperature vacuum low-pressure pulse carburizing process of 12Cr2Ni4A steel[J]. Journal of Northeastern University(Natural Science), 2020, 41(9): 1251-1256.
[5]赵振业. 航空高性能齿轮钢的研究与发展[J]. 航空材料学报, 2000, 20(3): 148-157.
Zhao Zhenye. Development of higher-performance aeronautical gear steel[J]. Journal of Aeronautical Materials, 2000, 20(3): 148-157.
[6]Krantz T, Tufts B. Pitting and bending fatigue evaluations of a new case-carburized gear steel[C]//ASME International Design Engineering Technical Conferences and Computers and Information in Engineering Conference. 2007: 863-869.
[7]黄斌, 朱洪武, 杨忠, 等. 渗碳温度对22Si2MnCrNi2MoA钢渗碳层的影响[J]. 材料热处理学报, 2013, 34(7): 136-141.
Huang Bin, Zhu Hongwu, Yang Zhong, et al. Influence of carburizing temperature on microstructure and properties of carburized layers of a 22Si2MnCrNi2MoA steel[J]. Transactions of Materials and Heat Treatment, 2013, 34(7): 136-141.
[8]黄帅, 张国强, 王毛球, 等. 不同渗碳层深度下重载齿轮钢的疲劳性能[J]. 钢铁研究学报, 2012, 24(4): 34-38.
Huang Shuai, Zhang Guoqiang, Wang Maoqiu, et al. Fatigue properties of heavy-duty gear steel with different carburized depth[J]. Journal of Iron and Steel Research, 2012, 24(4): 34-38.
[9]王斌, 何燕萍, 王昊杰, 等. 航空齿轮钢16Cr3NiWMoVNbE的真空低压渗碳[J]. 材料研究学报, 2020, 34(1): 35-42.
Wang Bin, He Yanping, Wang Haojie, et al. Vacuum low-pressure carburization of gear steel 16Cr3NiWMoVNbE for aviation[J]. Chinese Journal of Materials Research, 2020, 34(1): 35-42.
[10]An Xiaoxue, Tian Yong, Wang Bin, et al. Prediction of the formation of carbide network on grain boundaries in carburizing of 18CrNiMo7-6 steel alloys[J]. Surface and Coatings Technology, 2021, 421: 127348.
[11]王志新, 施建军, 梅俊歌, 等. 20CrNi2Mo钢真空渗碳工艺及数值模拟[J]. 金属热处理, 2017, 42(11): 117-122.
Wang Zhixin, Shi Jianjun, Mei Junge, et al. Numerical simulation on vacuum carburization of 20CrNi2Mo steel[J]. Heat Treatment of Metals, 2017, 42(11): 117-122.
[12]Zajusz M, Tkacz-S＇ K, Danielewski M. Modeling of vacuum pulse carburizing of steel[J]. Surface and Coatings Technology, 2014, 258: 646-651.
[13]赵振业. 超高强度钢中二次硬化现象研究[J]. 航空材料学报, 2002, 22(4): 46-55.
Zhao Zhenye. Studing status on the secondary hardening phenomenon in ultra-high strength steels[J]. Journal of Aeronautical Materials, 2002, 22(4): 46-55.
[14]杨雨松, 王斌. 航空轴承钢M50NiL真空低压渗碳热处理工艺研究[J]. 轧钢, 2020, 37(5): 35-38, 46.
Yang Yusong, Wang Bin. Investigation on vacuum low-pressure carburizing heat treatment process of bearing steel M50NiL for aviation engine[J]. Steel Rolling, 2020, 37(5): 35-38, 46.
[15]王会, 王昊杰, 贾涛, 等. 航空轴承钢的真空低压渗碳工艺[J]. 金属热处理, 2020, 45(1): 1-5.
Wang Hui, Wang Haojie, Jia Tao, et al. Low pressure carburizing process for aviation bearing steel[J]. Heat Treatment of Metals, 2020, 45(1): 1-5.

航空齿轮钢C69高温渗碳后的组织性能

Microstructure and properties of C69 gear steel for aviation after high temperature carburizing

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王英虎, 郑淮北, 刘庭耀, 宋令玺, 白青青. 固溶处理对53Cr21Mn9Ni4N耐热钢组织及碳化物的影响[J]. 金属热处理, 2022, 47(4): 39-45.
[2]	苏勇, 王帅, 王吉星, 于兴福, 刘洪秀, 刘金玲. 复合化学热处理对G13Cr4Mo4Ni4V钢组织和硬度的影响[J]. 金属热处理, 2022, 47(4): 226-230.
[3]	吴方俊, 邓小云, 揭晓华, 郑开宏, 骆智超. 热作模具用H13和Dievar钢的热疲劳性能[J]. 金属热处理, 2022, 47(3): 165-172.
[4]	李阔, 孙明月, 徐斌, 李殿中. 稀土H13模具钢横向冲击性能影响因素分析[J]. 金属热处理, 2022, 47(3): 181-185.
[5]	戴彦璋, 韩顺, 厉勇, 周敏, 王春旭. 回火温度对新一代传动齿轮钢C61组织及性能的影响[J]. 金属热处理, 2022, 47(1): 49-55.
[6]	李亮军, 张家敏, 迟宏宵, 周健. Co微合金化对M2高速钢组织和性能的影响[J]. 金属热处理, 2022, 47(1): 73-78.
[7]	邓彪, 陈蓬, 王国栋. 回火温度对二次硬化马氏体不锈钢组织和性能的影响[J]. 金属热处理, 2021, 46(9): 65-71.
[8]	李其, 陈正宗, 蒋新亮, 刘正东, 左良. 固溶温度对改型In617合金组织和性能的影响[J]. 金属热处理, 2021, 46(8): 109-114.
[9]	庄权, 王雨田, 董智鹏. 高碳铬轴承钢网状碳化物评价标准的对比分析[J]. 金属热处理, 2021, 46(6): 27-30.
[10]	徐琛, 陈广兴, 张勇伟, 谭騛, 许晓嫦. 1.25Cr-0.5Mo钢热处理后的组织与力学性能[J]. 金属热处理, 2021, 46(6): 200-204.
[11]	保顺, 刘荣佩, 丰涵, 佴启亮, 贾建, 朱玉亮, 宋志刚. 热等静压成形FeCrAl不锈钢的组织及脆性分析[J]. 金属热处理, 2021, 46(5): 9-13.
[12]	马长文, 马龙腾, 王彦锋, 杨永达, 韩承良. 终冷温度对低屈强比复合析出强化钢组织与性能的影响[J]. 金属热处理, 2021, 46(4): 131-137.
[13]	李灿明. 回火温度对1100 MPa钢组织和性能的影响[J]. 金属热处理, 2021, 46(4): 143-146.
[14]	常永, 李立, 吴少君, 左鹏鹏, 吴晓春. 球化温度对4Cr5Mo2V热作模具钢组织和性能的影响[J]. 金属热处理, 2021, 46(3): 46-50.
[15]	杜星霖, 鞠泉, 马惠萍, 杜金辉. GH3230合金M₂₃C₆型碳化物的析出行为[J]. 金属热处理, 2021, 46(2): 50-54.