1.5Al中锰钢短时临界退火后的组织与性能

doi:10.13251/j.issn.0254-6051.2022.05.022

摘要/Abstract

摘要： 应用热力学软件、扫描电镜(SEM)、X射线衍射仪(XRD)以及拉伸试验等方法研究了0.2C-5Mn-0.5Si-1.5Al中锰TRIP钢的热力学工艺窗口、微观结构及力学性能,并在此基础上分析了短时临界退火温度对组织演变和力学性能的影响规律。热力学计算结果表明,最佳临界退火温度范围为640~670 ℃,实际最佳退火温度右移约70 ℃。低温阶段(700 ℃)碳化物未完全溶解,高温阶段(760~820 ℃)奥氏体稳定性降低,组织中出现马氏体,分别对应最佳工艺窗口两侧。730 ℃临界退火后,碳化物完全溶解且奥氏体足够稳定,组织由铁素体和奥氏体构成,可获得最佳力学性能,抗拉强度约1041 MPa,屈服强度921 MPa,伸长率42%,强塑积接近43 GPa·%。

关键词: 中锰钢, 短时临界退火, 残留奥氏体, 力学性能

Abstract: Thermodynamic process window, microstructure and mechanical properties of 0.2C-5Mn-0.5Si-1.5Al medium manganese TRIP steel were studied by means of thermodynamic software, scanning electron microscopy (SEM), X-ray diffractometer (XRD) and tensile test, based on which, the effect of short time intercritical annealing temperature on microstructure evolution and mechanical properties of the tested steel was analyzed. The thermodynamic calculation results show that the optimal intercritical annealing temperature range is 640-670 ℃, and the actual optimal annealing temperature shifts to the right about 70 ℃. At the low temperature stage (700 ℃), the carbides are not completely dissolved, while at the high temperature stage (760-820 ℃), the stability of austenite decreases and martensite appears in the microstructure, which corresponding to both sides of the optimal process window respectively. After intercritical annealed at 730 ℃, the carbides are completely dissolved and the austenite is stable enough, the microstructure is composed of ferrite and austenite, and the optimal mechanical properties can be obtained, with the tensile strength of 1041 MPa, the yield strength of 921 MPa, the elongation of 42%, and the strength-elongation product being close to 43 GPa·%.

Key words: medium manganese steel, short time intercritical annealing, retained austenite, mechanical properties

中图分类号:

TG156.21

冯继科, 定巍, 李岩, 张光莹, 张楠. 1.5Al中锰钢短时临界退火后的组织与性能[J]. 金属热处理, 2022, 47(5): 136-140.

Feng Jike, Ding Wei, Li Yan, Zhang Guangyin, Zhang Nan. Microstructure and properties of 1.5Al medium-manganese steel after short time intercritical annealing[J]. Heat Treatment of Metals, 2022, 47(5): 136-140.

参考文献

[1]Mishra Gyanaranjan, Chandan Avanish Kumar. Effect of cold deformation extent and ART annealing duration on the microstructure and mechanical properties of a medium manganese steel[J]. Materials Chemistry and Physics, 2021, 271: 124940.
[2]Zhang Zherui, Song Renbo, Zhou Naipeng, et al. Microstructure evolution and mechanical properties of 67 GPa·% grade medium manganese steel[J]. Materials Science Forum, 2021, 6114: 404-409.
[3]Jing Songyang, Ding Hua, Ren Yuping, et al. A new insight into annealing parameters in tailoring the mechanical properties of a medium Mn steel[J]. Scripta Materialia, 2021, 202: 114019.
[4]Wang Chao, Yu Liming, Ding Ran, et al. Microstructure and mechanical properties of a novel medium Mn steel with Cr and Mo microalloying[J]. Materials Science and Engineering A, 2021, 825: 141926.
[5]冯树明, 万德成, 王亚婷, 等. Q&P处理低碳中锰钢的显微组织与力学性能[J]. 金属热处理, 2020, 45(4): 69-74.
Feng Shuming, Wan Decheng, Wang Yating, et al. Microstructure and mechanical properties of low carbon medium manganese steel treated by Q&P process[J]. Heat Treatment of Metals, 2020, 45(4): 69-74.
[6]刘腾, 朱政强. 第三代汽车用中锰钢研究现状[J]. 兵器材料科学与工程, 2019, 42(6): 102-108.
Liu Teng, Zhu Zhengqiang. Research status of medium-manganese steel for the 3^rd generation automobile sheet[J]. Ordnance Material Science and Engineering, 2019, 42(6): 102-108.
[7]田亚强, 曹仲乾, 潘红波, 等. 两相区温度对中锰钢IQ&P处理后组织和力学性能的影响[J]. 金属热处理, 2020, 45(7): 37-41.
Tian Yaqiang, Cao Zhongqian, Pan Hongbo, et al. Effect of intercritical temperature on the microstructure and mechanical properties of medium manganese steel after IQ&P treatment[J]. Heat Treatment of Metals, 2020, 45(7): 37-41.
[8]李岩, 付吉雪, 赵增武, 等. Nb和时效时间对热轧中锰TRIP钢中P偏聚的影响[J]. 金属热处理, 2020, 45(3): 59-63.
Li Yan, Fu Jixue, Zhao Zengwu, et al. Effect of Nb and aging time on phosphorus segregation in hot-rolled medium-manganese TRIP steel[J]. Heat Treatment of Metals, 2020, 45(3): 59-63.
[9]Chen Jun, Liu Zhenyu. The combination of strength and cryogenic impact toughness in low carbon 5Mn-5Ni steel[J]. Journal of Alloys and Compounds, 2020, 837: 155484.
[10]Shan Chen, Chen Shan, Zhao Xianming, et al. Effect of prior austenite grain size on bainitic transformation above and below Ms in medium Mn steel[J]. Journal of Physics: Conference Series, 2020, 1653: 012043.
[11]Fan Lifeng, Li Sai, Zhao Yan, et al. Effect of a two-phase region annealing process on microstructure and mechanical properties of medium manganese steel[J]. Ironmaking and Steelmaking, 2020, 47(8): 865-872.
[12]Hou Feifei, Bai Yu, Akinobu Shibata, et al. Microstructure evolution during thermomechanical processing in 3Mn-0.1C medium-Mn steel[J]. Materials Science and Technology, 2019, 35(17): 2101-2108.
[13]Chen Silian, Cao Zhaoxi, Wang Chang, et al. Effect of volume fraction and mechanical stability of austenite on ductility of medium Mn steel[J]. Journal of Iron and Steel Research International, 2019, 26(11): 1209-1218.
[14]孙荣民, 李国阳, 王辉, 等. 逆相变退火处理Fe-Mn-C中锰钢的组织与性能[J]. 钢铁, 2021, 56(6): 82-88.
Sun Rongmin, Li Guoyang, Wang Hui, et al. Microstructure and properties of Fe-Mn-C medium-Mn steel processed by ART-annealing[J]. Iron and Steel, 2021, 56(6): 82-88.
[15]邵成伟, 王俊涛, 赵晓丽, 等. 两相区退火处理含铝中锰钢的组织和力学性能[J]. 钢铁, 2020, 55(5): 87-93.
Shao Chengwei, Wang Juntao, Zhao Xiaoli, et al. Microstructure and mechanical properties of intercritically annealed Al-contain medium Mn steel[J]. Iron and Steel, 2020, 55(5): 87-93.
[16]杨丽芳, 魏焕君, 孙力, 等. 退火温度对冷轧中锰钢组织性能和断裂行为的影响[J]. 钢铁, 2019, 54(11): 80-87, 100.
Yang Lifang, Wei Huanjun, Sun Li, et al. Effect of annealing temperatures on the microstructures, mechanical properties and fracture behavior of cold-rolled medium-Mn steel[J]. Iron and Steel, 2019, 54(11): 80-87, 100.
[17]朱延山, 罗咪, 武凤娟, 等. Fe-0.3C-5Mn-3Al超细晶钢的室温拉伸力学行为[J]. 钢铁研究学报, 2019, 31(12): 1108-1114.
Zhu Yanshan, Luo Mi, Wu Fengjuan, et al. Room-temperature tensile mechanical behavior of Fe-0.3C-5Mn-3Al ultra-fine grained steels[J]. Journal of Iron and Steel Research, 2019, 31(12): 1108-1114.
[18]Cullity B D, Stock S R. Elements of X-ray Diffraction[M]. 3rd edition. New York: Prentice-Hall, 2001.
[19]Moor Emmanuel De, Matlock David K, Speer John G, et al. Austenite stabilization through manganese enrichment[J]. Scripta Materialia, 2011, 64(2): 185-188.
[20]John SAristeidakis, Gregory N Haidemenopoulos. Alloy design based on computational thermodynamics and multi-objective optimization: The case of medium-Mn steels[J]. Metallurgical and Materials Transactions, 2017, 48(5): 2584-2602.
[21]王润勋, 王宝峰, 李岩, 等. 0.2C-5Mn-1.5Al中锰TRIP钢的显微组织及力学性能[J]. 金属热处理, 2020, 45(4): 63-68.
Wang Runxun, Wang Baofeng, Li Yan, et al. Microstructure and mechanical properties of 0.2C-5Mn-1.5Al medium manganese TRIP steel[J]. Heat Treatment of Metals, 2020, 45(4): 63-68.
[22]雷志国, 王存宇, 周峰峦, 等. 深冷对逆相变处理中锰钢组织性能的影响[J]. 钢铁研究学报, 2021, 33(4): 330-335.
Lei Zhiguo, Wang Cunyu, Zhou Fengluan, et al. Effect of cryogenic treatment on microstructure and properties of medium-manganese steel treated by ART-annealing[J]. Journal of Iron and Steel Research, 2021, 33(4): 330-335.
[23]崔海军, 王春风, 桑振远, 等. 退火对汽车用0.1C-7Mn-0.3Si中锰钢组织与力学性能的影响[J]. 热加工工艺, 2020, 49(18): 135-137.
Cui Haijun, Wang Chunfeng, Sang Zhenyuan, et al. Effect of annealing on the microstructure and mechanical properties of 0.1C-7Mn-0.3Si medium manganese steel for automobile[J]. Hot Working Technology, 2020, 49(18): 135-137.
[24]刘春泉, 彭其春, 薛正良, 等. 不同热处理工艺对Nb-Mo中锰钢组织和力学性能的影响[J]. 钢铁研究学报, 2019, 31(12): 1100-1107.
Liu Chunquan, Peng Qichun, Xue Zhengliang, et al. Effect of different heat treatment processes on microstructure and mechanical properties of Nb-Mo microalloyed medium-Mn steel[J]. Journal of Iron and Steel Research, 2019, 31(12): 1100-1107.
[25]田亚强, 黎旺, 郑小平, 等. 两相区退火热轧中锰钢碳化物析出行为与组织性能研究[J]. 材料导报, 2019, 33(16): 2765-2770.
Tian Yaqiang, Li Wang, Zheng Xiaoping, et al. Study on carbide precipitation behavior and microstructure and mechanical property of intercritically annealed hot-rolled medium manganese steel[J]. Materials Review, 2019, 33(16): 2765-2770.
[26]Zhang Yu, Ding Hua, Zhu Haokun, et al. A novel method to define the effective average grain size of the materials with lath-typed microstructure: An example of medium manganese steel[J]. Vacuum, 2021, 191: 110313.
[27]Bai Shaobin, Xiao Wentao, Niu Weiqiang, et al. Microstructure and mechanical properties of a medium-Mn steel with 1.3 GPa-strength and 40%-ductility[J]. Materials, 2021, 14(9): 2233.
[28]Zou Yuming, Ding Hua, Tang Zhengyou. Effect of carbon content on deformation behavior and partitioning of manganese in medium-Mn steels[J]. Metals, 2021, 11(4): 11040667.
[29]Yang Dapeng, Du Pengju, Wu Di, et al. The microstructure evolution and tensile properties of medium-Mn steel heat-treated by a two-step annealing process[J]. Journal of Materials Science and Technology, 2021, 75(16): 205-215.
[30]张馨月, 冯运莉, 曹阔. 退火温度对中锰TRIP钢组织和性能的影响[J]. 金属热处理, 2020, 45(7): 23-27.
Zhang Xinyue, Feng Yunli, Cao Kuo. Effect of annealing temperature on microstructure and properties of medium manganese TRIP steel[J]. Heat Treatment of Metals, 2020, 45(7): 23-27.