轧制变形量对Mg-Zn-Y合金组织和性能的影响

doi:10.13251/j.issn.0254-6051.2022.06.007

金属热处理 ›› 2022, Vol. 47 ›› Issue (6): 39-45.DOI: 10.13251/j.issn.0254-6051.2022.06.007

轧制变形量对Mg-Zn-Y合金组织和性能的影响

翟传田^1,2, 孙有平^1,2,3, 何江美^1,2,3, 孟祥超^1,2, 万斯雨^1,2

1.广西科技大学机械与汽车工程学院, 广西柳州 545006;
2.广西土方机械协同创新中心, 广西柳州 545006;
3.广西汽车零部件与整车技术重点实验室, 广西柳州 545006

收稿日期:2022-02-15 修回日期:2022-04-15 出版日期:2022-06-25 发布日期:2022-07-05
通讯作者: 孙有平,教授,博士,E-mail: syptaiji@126.com
作者简介:翟传田(1995—),男,硕士研究生,主要研究方向为镁合金的塑性成形及阻尼性能,E-mail:15563851750@163.com。
基金资助:
中央引导地方科技发展专项(2021ZYZX1012);柳州市科技计划(2021CBA0102);广西高等学校高水平创新团队资助项目(桂教师范[2019]52号);广西研究生教育创新计划(YCSW2020221);广西科技大学研究生教育创新计划(GKYC202110)

Effect of rolling deformation on microstructure and properties of Mg-Zn-Y alloy

Zhai Chuantian^1,2, Sun Youping^1,2,3, He Jiangmei^1,2,3, Meng Xiangchao^1,2, Wan Siyu^1,2

1. School of Mechanical and Automotive Engineering, Guangxi University of Science and Technology, Liuzhou Guangxi 545006, China;
2. Guangxi Earthmoving Machinery Collaborative Innovation Center, Liuzhou Guangxi 545006, China;
3. Guangxi Key Laboratory of Automobile Components and Vehicle Technology, Liuzhou Guangxi 545006, China

Received:2022-02-15 Revised:2022-04-15 Online:2022-06-25 Published:2022-07-05

摘要/Abstract

摘要： 使用光学显微镜、动态机械热分析仪、X射线衍射仪和扫描电镜研究了不同轧制变形量对Mg-4Zn-2Y和Mg-4Zn-4Y合金显微组织、力学性能及阻尼性能的影响。结果表明,经轧制后合金中出现片层状的LPSO相;两种合金阻尼性能中与应变振幅无关的阻尼性能Q^-1₀随着轧制变形量的增加,其变化趋势基本一致,与应变振幅相关的阻尼性能Q^-1_h随着轧制变形量的增加而降低,Mg-4Zn-2Y合金以及Mg-4Zn-4Y合金的阻尼机制为位错型阻尼;随着轧制变形量的增加,合金断口中的韧窝数量增加,解理面减少,主要断裂方式由脆性断裂转变为韧性断裂;相同轧制变形量下,Mg-4Zn-4Y合金的强度优于Mg-4Zn-2Y合金,而阻尼性能要低于Mg-4Zn-2Y合金。

关键词: Mg-Zn-Y合金, 阻尼性能, 轧制变形, 力学性能, 组织

Abstract: Effect of different rolling deformation on microstructure, mechanical properties and damping properties of Mg-4Zn-2Y alloy and Mg-4Zn-4Y alloy was investigated by means of optical microscope, dynamic mechanical thermal analyzer, X-ray diffraction and scanning electron microscope. The experimental results show that the lamellar LPSO phase appears in the alloy after rolling. With the increase of rolling deformation, the change of damping property Q^-1₀ that is independent of strain amplitude is basically the same, and the damping property Q^-1_h related to the strain amplitude decreases with the increase of rolling deformation. The damping mechanism of the Mg-4Zn-2Y alloy and Mg-4Zn-4Y alloy are the dislocation damping. With the increase of rolling deformation, the number of dimples in the fracture surface of the alloy increases, the dissociation surface decreases, thus the fracture mode changes from brittle fracture to ductile fracture. Under the same rolling deformation, the tensile strength of the Mg-4Zn-4Y alloy is higher than that of the Mg-4Zn-2Y alloy, but the damping capacity is lower than that of Mg-4Zn-2Y alloy.

Key words: Mg-Zn-Y alloy, damping capacity, rolling deformation, mechanical properties, microstructure

中图分类号:

TG146.4

翟传田, 孙有平, 何江美, 孟祥超, 万斯雨. 轧制变形量对Mg-Zn-Y合金组织和性能的影响[J]. 金属热处理, 2022, 47(6): 39-45.

Zhai Chuantian, Sun Youping, He Jiangmei, Meng Xiangchao, Wan Siyu. Effect of rolling deformation on microstructure and properties of Mg-Zn-Y alloy[J]. Heat Treatment of Metals, 2022, 47(6): 39-45.

参考文献

[1]刘筱, 王洋洋, 叶俊宏, 等. AZ31镁合金高应变速率轧制宏微观仿真[J]. 材料导报, 2021, 35(14): 14101-14106.
Liu Xiao, Wang Yangyang, Ye Junhong, et al. Macro-micro simulation of AZ31 magnesium alloy under high strain rate rolling[J]. Materials Reports, 2021, 35(14): 14101-14106.
[2]陈宇, 刘红梅, 王峰阳, 等. Mg-Sn合金的阻尼机理研究[J]. 金属热处理, 2017, 42(4): 18-21.
Chen Yu, Liu Hongmei, Wang Fengyang, et al. Damping mechanism of Mg-Sn alloy[J]. Heat Treatment of Metals, 2017, 42(4): 18-21.
[3]Yang Y, Xiong X M, Chen J, et al. Research advances in magnesium and magnesium alloys worldwide in 2020[J]. Journal of Magnesium and Alloys, 2021, 9(3): 705-747.
[4]冯旭辉, 孙有平, 何江美, 等. 热处理对大应变轧制ZK60镁合金阻尼峰的影响[J]. 特种铸造及有色合金, 2019, 39(12): 1287-1290.
Feng Xuhui, Sun Youping, He Jiangmei, et al. Effects of heat treatment on damping peak of ZK60 magnesium Al in high strain rolling[J]. Special Casting & Nonferrous Alloys, 2019, 39(12): 1287-1290.
[5]梁爽, 黄福祥, 张照超, 等. 合金化及热处理对Al-32%Zn合金组织和阻尼性能的影响[J]. 金属热处理, 2019, 44(8): 77-83.
Liang Shuang, Huang Fuxiang, Zhang Zhaochao, et al. Effects of alloying and heat treatment on microstructure and damping performance of Al-32%Zn alloy[J]. Heat Treatment of Metals, 2019, 44(8): 77-83.
[6]赖林. Mg-Mn-Zn系镁合金组织与性能研究[D]. 北京: 北京有色金属研究总院, 2017.
[7]宋鹏飞, 王敬丰, 周小蒽, 等. Zn含量对Mg-10Gd-6Y-xZn-0.6Zr合金显微组织、力学和阻尼性能的影响[J]. 中国有色金属学报, 2012, 22(9): 2430-2438.
Song Pengfei, Wang Jingfeng, Zhou Xiaoen, et al. Effects of Zn content on microstructure, mechanical properties and damping capacities of Mg-10Gd-6Y-xZn-0.6Zr alloys[J]. Chinese Journal of Nonferrous Metals, 2012, 22(9): 2430-2438.
[8]Lu R P, Wang J F, Ding Z B, et al. Effect of long period stacking ordered phase on damping capacities of as-cast Mg-Zn-Y alloys[J]. Journal of Measurement Science and Instrumentation, 2017, 8(3): 283-288.
[9]Somekawaa H, Watanabeb H, Mukaic T. Effect of solute atoms on grain boundary sliding in magnesium alloys[J]. Philosophical Magazine, 2014, 94(12): 1345-1360.
[10]鲁若鹏. Mg-Zn-Y合金中LPSO相的调控及其对阻尼和力学性能的影响机制研究[D]. 重庆: 重庆大学, 2015.
[11]Luo Suqin, Tang Aitao, Pan Fusheng, et al. Effect of mole ratio of Y to Zn on phase constituent of Mg-Zn-Zr-Y alloys[J]. Transactions of Nonferrous Metals Society of China, 2011, 21(4): 795-800.
[12]冯旭辉, 孙有平, 何江美. 铸态Mg-xSn-1Mn合金的显微组织和阻尼性能[J]. 金属热处理, 2020, 45(5): 29-34.
Feng Xuhui, Sun Youping, He Jiangmei. Microstructure and damping property of as-cast Mg-xSn-1Mn alloy[J]. Heat Treatment of Metals, 2020, 45(5): 29-34.
[13]刘筱, 朱必武, 李落星, 等. 挤压态AZ31镁合金热变形过程中的孪生和织构演变[J]. 中国有色金属学报, 2016, 26(2): 288-295.
Liu Xiao, Zhu Biwu, Li Luoxing, et al. Twinning and texture evolution in extruded AZ31 magnesium alloy during hot deformation[J]. The Chinese Journal of Nonferrous Metals, 2016, 26(2): 288-295.
[14]Zhang D, Zhen T, Huo Q, et al. Dynamic recrystallization behaviors of Mg-Gd-Y-Zn-Zr alloy with different morphologies and distributions of LPSO phases[J]. Materials Science and Engineering A, 2017, 715: 389-403.
[15]张军, 寇子明, 杨亚琴, 等. AZ31和ZK60变形镁合金阻尼性能的研究[J]. 兵器材料科学与工程, 2017, 40(3): 115-118.
Zhang Jun, Kou Ziming, Yang Yaqin, et al. Damping properties of AZ31 and ZK60 wrought magnesium alloys[J]. Ordnance Material Science and Engineering, 2017, 40(3): 115-118.
[16]刘先兰, 刘楚明, 常亚, 等. 高阻尼高强度镁合金的研究现状及展望[J]. 铸造, 2008(11): 1123-1127.
Liu Xianlan, Liu Chuming, Chang Ya, et al. Research status and development progress of high-damping and high strength magnesium alloys[J]. Foundry, 2008(11): 1123-1127.
[17]Hu X S, Wu K, Zheng M Y, et al. Low frequency damping capacities and mechanical properties of Mg-Si alloys[J]. Materials Science & Engineering A, 2007, 452: 374-379.
[18]Rogers D H. An extension of a theory of mechanical damping due to dislocations[J]. Journal of Applied Physics, 1962, 33(3): 781-792.
[19]张佳, 朱红梅, 吴炜. 轧制变形对Mg-0.6Zr合金阻尼性能的影响[J]. 热加工工艺, 2014, 43(14): 53-55.
Zhang Jia, Zhu Hongmei, Wu Wei. Effect of rolling on damping capacity of Mg-0.6Zr alloy[J]. Hot Working Technology, 2014, 43(14): 53-55.
[20]王敬丰, 高珊, 潘复生, 等. 加工工艺对ZK60镁合金力学性能和阻尼性能的影响[J]. 中国有色金属学报, 2009, 19(5): 821-825.
Wang Jinfeng, Gao Shan, Pan Fusheng, et al. Influence of process technology on mechanical and damping properties of ZK60 magnesium alloys[J]. Chinese Journal of Nonferrous Metals, 2009, 19(5): 821-825.
[21]史菲. Mg-Zn-Y(-Gd)镁合金凝固组织与性能的研究[D]. 哈尔滨: 哈尔滨工业大学, 2015.

轧制变形量对Mg-Zn-Y合金组织和性能的影响

Effect of rolling deformation on microstructure and properties of Mg-Zn-Y alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	谷国超, 李瑞芬, 辛振民, 相立新, 许文花, 吕宇鹏. 固溶温度对2507双相不锈钢力学性能及耐蚀性的影响[J]. 金属热处理, 2022, 47(6): 1-6.
[2]	吴杨, 黄晖, 石薇, 文胜平, 吴晓蓝, 荣莉, 魏午. 固溶时效处理对Al-Cu-Mn-Er铸造合金力学性能和显微组织的影响[J]. 金属热处理, 2022, 47(6): 7-12.
[3]	贾新云, 陈升平, 宗毳, 谭永宁, 黄朝晖. DD5合金单晶双联整铸导向叶片的热工艺匹配性[J]. 金属热处理, 2022, 47(6): 13-18.
[4]	田亚强, 赵志浩, 杨子旋, 徐海卫, 韩赟, 郑小平, 李红斌, 陈连生. 温轧温度对中碳钢组织与力学性能的影响[J]. 金属热处理, 2022, 47(6): 19-24.
[5]	蒋明忠, 赵勇, 潘钱付, 吴裕, 王馨敏, 蒋文龙. F/M钢包壳管材热处理工艺优化[J]. 金属热处理, 2022, 47(6): 25-32.
[6]	李晓琛, 王世颖, 华天宇, 陈智栋. 深冷处理对TC4钛合金退火过程中微观组织和力学性能的影响[J]. 金属热处理, 2022, 47(6): 46-53.
[7]	冯树明, 万德成, 胡进朋, 李杰. 配分温度对0.2C-2.96Mn-1.73Si钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(6): 54-58.
[8]	陈佳俊, 朱治愿, 李建强, 王守乾. 固溶处理对Cr23Ni7Mo2Cu0.6双相不锈钢组织与性能的影响[J]. 金属热处理, 2022, 47(6): 59-63.
[9]	白兴红, 赵席春, 赵德利, 王大鹏, 南玉静. 冷却速度对支承辊用Cr5钢显微组织与力学性能的影响[J]. 金属热处理, 2022, 47(6): 69-71.
[10]	徐新犬, 方舟, 刘新宽, 王子延. 热处理对铜铝低温钎焊的影响[J]. 金属热处理, 2022, 47(6): 78-84.
[11]	严翔, 李德发, 官计生, 杨治争. 形变对低碳微合金化热处理钢组织和性能的影响[J]. 金属热处理, 2022, 47(6): 85-88.
[12]	韩颢源, 杨涛, 邱娟, 杨刚, 余万华, 翟月雯, 周乐育. 固溶处理对TC4合金组织和硬度的影响[J]. 金属热处理, 2022, 47(6): 93-97.
[13]	钟彬, 陈义庆, 李琳, 高鹏, 伞宏宇, 艾芳芳, 田秀梅. 淬火油温对40CrMnMo钢钻杆组织和性能的影响[J]. 金属热处理, 2022, 47(6): 98-102.
[14]	赵天生, 方羽, 孙誉宾. 成形速度对7050铝合金锻件力学性能和断口形貌的影响[J]. 金属热处理, 2022, 47(6): 103-106.
[15]	舒玮, 王丽英. 固溶处理对奥氏体不锈钢07Cr18Ni11Nb高温力学性能的影响[J]. 金属热处理, 2022, 47(6): 107-110.