轴承用8Cr4Mo4V钢真空气淬及等温盐浴淬火后的性能对比分析

doi:10.13251/j.issn.0254-6051.2022.07.002

金属热处理 ›› 2022, Vol. 47 ›› Issue (7): 9-14.DOI: 10.13251/j.issn.0254-6051.2022.07.002

轴承用8Cr4Mo4V钢真空气淬及等温盐浴淬火后的性能对比分析

童锐¹, 于兴福², 刘永宝¹, 夏云志¹, 苏勇³, 金映丽²

1.中国航发哈尔滨轴承有限公司, 黑龙江哈尔滨 150500;
2.沈阳工业大学机械工程学院, 辽宁沈阳 110870;
3.沈阳化工大学机械与动力工程学院, 辽宁沈阳 110142

收稿日期:2022-02-25 修回日期:2022-05-16 出版日期:2022-07-25 发布日期:2022-08-12
通讯作者: 于兴福,副教授,E-mail:yuxingfu@163.com
作者简介:童锐(1990—),女,硕士,工程师,主要研究方向为轴承钢热处理,E-mail:ss199089@126.com。
基金资助:
国家重点研发计划(2020YFB2007800)

Comparative analysis on properties of 8Cr4Mo4V steel for bearing after vacuum gas quenching and isothermal salt bath quenching

Tong Rui¹, Yu Xingfu², Liu Yongbao¹, Xia Yunzhi¹, Su Yong³, Jin Yingli²

1. AECC Harbin Bearing Co., Ltd., Harbin Heilongjiang 150500, China;
2. School of Mechanical Engineering, Shenyang University of Technology, Shenyang Liaoning 110870, China;
3. School of Mechanical and Power Engineering, Shenyang University of Chemical Technology, Shenyang Liaoning 110142, China

Received:2022-02-25 Revised:2022-05-16 Online:2022-07-25 Published:2022-08-12

摘要/Abstract

摘要： 通过显微组织观察及性能测定,对轴承用8Cr4Mo4V钢真空气淬及等温盐浴淬火处理后的性能进行了对比分析。结果表明,8Cr4Mo4V钢真空气淬后得到马氏体组织,等温盐浴淬火后得到马氏体+贝氏体混合组织。真空气淬后钢的晶界有碳化物析出,腐蚀后晶界特征明显,而等温盐浴淬火后晶界碳化物析出量少,钢的晶界特征不明显。再经回火处理后,钢中析出大量碳化物,与真空气淬相比,等温盐浴淬火钢中析出的碳化物在尺寸和数量上都更大。钢的硬度和耐磨性测试表明,等温盐浴淬火钢的硬度为61.78 HRC,而真空气淬钢的硬度为60.28 HRC,硬度提高了1.5 HRC,等温盐浴淬火钢的摩擦磨损性能比真空气淬钢高。与真空气淬相比,等温盐浴淬火处理后钢的力学性能提升,室温拉伸强度提高了164 MPa,高温拉伸强度提高了50 MPa,冲击吸收能量提高了46.9%,旋转弯曲疲劳强度极限由860 MPa提高至1050 MPa,提高了22%。

关键词: 高温轴承钢, 真空气淬, 等温盐浴淬火, 碳化物, 力学性能

Abstract: Properties of 8Cr4Mo4V steel for bearing after vacuum gas quenching and isothermal salt bath quenching were comparatively analyzed by microstructure observation and property test. The results show that the martensite in the 8Cr4Mo4V steel is obtained after vacuum quenching, while the mixed microstructure of martensite and bainite is obtained after isothermal salt bath quenching. There is carbide precipitation at the grain boundary of vacuum quenched steel, and the grain boundary characteristics are obviously shown after chemical etching. However, the amount of carbide precipitation at the grain boundary of isothermal salt bath quenched steel is less, and the grain boundary characteristics of the steel are not obvious. Then after tempering treatment, a large number of carbides precipitate in the steels, and that in the steel isothermal salt bath quenched are larger in size and quantity than that of vacuum quenched. The test results of hardness and wear resistance show that the hardness of the isothermal salt bath quenched steel is 61.78 HRC, higher by 1.5 HRC than that of the vacuum quenched steel (60.28 HRC). The friction and wear resistance of the isothermal salt bath quenched steel is higher than that of the vacuum quenched. Compared with that of vacuum quenching, the mechanical properties of the steel after isothermal salt bath quenching are better: the tensile strength is higher by 164 MPa and 50 MPa respectively at room temperature and at high temperature, the impact absorbed energy is increased by 46.9%, and the rotary bending fatigue strength is increased by 22%, from 860 MPa to 1050 MPa.

Key words: high temperature bearing steel, vacuum gas quenching, isothermal salt bath quenching, carbide, mechanical properties

中图分类号:

童锐, 于兴福, 刘永宝, 夏云志, 苏勇, 金映丽. 轴承用8Cr4Mo4V钢真空气淬及等温盐浴淬火后的性能对比分析[J]. 金属热处理, 2022, 47(7): 9-14.

Tong Rui, Yu Xingfu, Liu Yongbao, Xia Yunzhi, Su Yong, Jin Yingli. Comparative analysis on properties of 8Cr4Mo4V steel for bearing after vacuum gas quenching and isothermal salt bath quenching[J]. Heat Treatment of Metals, 2022, 47(7): 9-14.

参考文献

[1]周丽娜, 杨晓峰, 刘明, 等. 8Cr4Mo4V高温轴承钢热处理及表面改性技术的研究进展[J]. 轴承, 2021(8): 1-10.
Zhou Lina, Yang Xiaofeng, Liu Ming, et al. Research progress on heat treatment and surface modification technology of 8Cr4Mo4V high-temperature bearing steel [J]. Bearing, 2021(8): 1-10.
[2]刘洪秀, 于兴福, 魏英华, 等. 航空轴承钢的发展及热处理技术[J]. 航空制造技术, 2020, 63(1): 94-101.
Liu Hongxiu, Yu Xingfu, Wei Yinghua, et al. Development of aviation bearing steel and heat treatment technology [J]. Aeronautical Manufacturing Technology, 2020, 63(1): 94-101.
[3]田勇, 宋超伟, 葛泉江, 等. 航空用高温轴承钢CSS-42L热处理技术及其展望[J]. 轧钢, 2019, 36(6): 1-5, 28.
Tian Yong, Song Chaowei, Ge Quanjiang, et al. Status of research and development of heat treatment techniques for heat resistant bearing CSS-42L applied for aviation [J]. Steel Rolling, 2019, 36(6): 1-5, 28.
[4]刘汇河, 宋海涛, 姚颖才, 等. 8Cr4Mo4V异形滚子盐浴软氮化工艺试验[J]. 轴承, 2020(4): 15-18.
Liu Huihe, Song Haitao, Yao Yingcai, et al. Salt bath soft nitriding process test for special shaped rollers made of 8Cr4Mo4V [J]. Bearing, 2020(4): 15-18.
[5]刘秀莲, 班君, 罗燕, 等. 消除8Cr4Mo4V钢混晶试验研究[J]. 热加工工艺, 2018, 47(14): 165-168.
Liu Xiulian, Ban Jun, Luo Yan, et al. Experimental study on elimination of mixed grain of 8Cr4Mo4V steel [J]. Hot Working Technology, 2018, 47(14): 165-168.
[6]蔡欣, 孙明月, 王卫, 等. 8Cr4Mo4Ni4V航空轴承钢高温奥氏体晶粒长大的数学模型[J]. 材料工程, 2018, 46(9): 131-137.
Cai Xin, Sun Mingyue, Wang Wei, et al. Mathematical models of austenite grain growth of 8Cr4Mo4Ni4V aviation bearing steel at high temperature [J]. Journal of Materials Engineering, 2018, 46(9): 131-137.
[7]郑春雷, 佘丽, 王艳辉, 等. 高碳贝氏体轴承钢滚动接触疲劳性能的研究[J]. 机械工程学报, 2017, 53(24): 110-117.
Zheng Chunlei, She Li, Wang Yanhui, et al. Rolling contact fatigue behaviors of high carbon bainitic bearing steel [J]. Journal of Mechanical Engineering, 2017, 53(24): 110-117.
[8]杨雨松, 王斌. 航空轴承钢M50NiL真空低压渗碳热处理工艺研究[J]. 轧钢, 2020, 37(5): 35-38, 46.
Yang Yusong, Wang Bin. Investigation on vacuum low-pressure carburizing heat treatment process of bearing steel M50NiL for aviation engine [J]. Steel Rolling, 2020, 37(5): 35-38, 46.
[9]刘兆宾, 周丽娜, 罗甸, 等. 回火对 Cr4Mo4V钢电子束Cr合金化层组织和性能的影响[J]. 金属热处理, 2020, 45(8): 194-198.
Liu Zhaobing, Zhou Lina, Luo Dian, et al. Effect of tempering on microstructure and properties of Cr alloyed layer prepared by high current pulsed electron beam on Cr4Mo4V steel [J]. Heat Treatment of Metals, 2020, 45(8): 194-198.
[10]王松, 夏云志, 于兴福, 等. 尺寸稳定处理时8Cr4Mo4V 轴承钢的相变及其对尺寸变化的影响[J]. 轴承, 2019(3): 48-51.
Wang Song, Xia Yunzhi, Yu Xingfu, et al. Phase transformation during dimensional stability treatment and its effect on dimensional variation of bearing steel 8Cr4Mo4V [J]. Bearing, 2019(3): 48-51.
[11]沈伟毅, 李昭昆, 龚建勋, 等. Cr4Mo4V 钢轴承套圈尺寸稳定性热处理试验[J]. 热处理技术与装备, 2015, 36(3): 27-29.
Shen Weiyi, Li Zhaokun, Gong Jianxun, et al. Heat treatment test of size stability for bearing ring of Cr4Mo4V steel [J]. Heat Treatment Technology and Equipment, 2015, 36(3): 27-29.
[12]吝欢, 杨卯生, 舒佰坡. 8Cr4Mo4V高温轴承钢润滑条件下的微动磨损行为[J]. 材料热处理学报, 2019, 40(6): 143-154.
Lin Huan, Yang Maosheng, Shu Baipo. Fretting wear behavior of 8Cr4Mo4V high temperature bearing steel under lubrication condition [J]. Transactions of Materials and Heat Treatment, 2019, 40(6): 143-154.
[13]魏英华. 8Cr4Mo4V钢热处理组织与尺寸稳定性研究[D]. 沈阳: 沈阳工业大学, 2020.
Wei Yinghua. Study on heat treatment microstructure and dimensional stability of 8Cr4Mo4V steel [D]. Shenyang: Shenyang University of Technology, 2020.
[14]郭军, 杨卯生, 卢德宏, 等. Cr4Mo4V轴承钢旋转弯曲疲劳寿命及疲劳裂纹萌生机理[J]. 材料工程, 2019, 47(7): 134-143.
Guo Jun, Yang Maosheng, Lu Dehong, et al. Rolling contact fatigue and wear characteristics of Cr4Mo4V bearing steel [J]. Journal of Materials Engineering, 2019, 47(7): 134-143.
[15]吴玉成, 刘明, 付中元, 等. G80Cr4Mo4V钢角接触球轴承套圈锻件辗扩工艺改进[J]. 轴承, 2021(1): 35-38.
Wu Yucheng, Liu Ming, Fu Zhongyuan, et al. Improvement on rolling process of angular contact ball bearing ring forgings made of G80Cr4Mo4V steel [J]. Bearing, 2021(1): 35-38.

轴承用8Cr4Mo4V钢真空气淬及等温盐浴淬火后的性能对比分析

Comparative analysis on properties of 8Cr4Mo4V steel for bearing after vacuum gas quenching and isothermal salt bath quenching

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	姜超, 贾东永, 周志勇, 田政, 郭星晔, 王哲, 韩修柱. 激光选区熔化高强铝合金件的热处理及空间环境性能[J]. 金属热处理, 2022, 47(7): 1-8.
[2]	田紫维, 姚彦欣, 刘佳兴, 王智怡, 胡章权, 蒋波. 冷却速度对微合金化中碳非调质钢组织和性能的影响[J]. 金属热处理, 2022, 47(7): 27-33.
[3]	韦小园, 魏午, 郭骁, 程志强, 文胜平, 石薇, 黄晖. 退火处理对含铒Al-6Mg-1Mn铝合金组织和性能的影响[J]. 金属热处理, 2022, 47(7): 47-51.
[4]	王华, 王泽钰, 宋嘉明, 瞿宗宏, 赖运金, 梁书锦. 固溶处理对粉末冶金GH4099合金组织及性能的影响[J]. 金属热处理, 2022, 47(7): 86-91.
[5]	樊立峰, 亢泽, 贾丽英, 徐惠敏, 高军. 淬火后的逆相变退火温度对5%Mn冷轧中锰钢组织与性能的影响[J]. 金属热处理, 2022, 47(7): 92-97.
[6]	于晃, 王飞宇, 包翠敏, 王全振, 陈炜, 曲德毅, 蒋申柱, 马煜林. 真空时效加热到温时间滞后现象对FV520B钢组织及性能的影响[J]. 金属热处理, 2022, 47(7): 98-101.
[7]	陈波, 张继国, 华永兴, 尹树春, 吴磊, 梁振威, 孙扩. 高端车用热成形钢CR300MB的研发与应用[J]. 金属热处理, 2022, 47(7): 107-113.
[8]	付锡彬, 孟少博, 刘文胜, 张可, 李昭东, 曹燕光, 章小峰, 雍岐龙. 固溶处理对Fe-30Mn-10Al-1C低密度钢组织及力学性能的影响[J]. 金属热处理, 2022, 47(7): 114-119.
[9]	韩俊刚, 邵志文, 宋运坤, 陈小虎, 丁博远, 顾娇娇. 热处理对针阀体用4Cr5MoSiV1钢组织及性能的影响[J]. 金属热处理, 2022, 47(7): 120-124.
[10]	许荣昌, 王毅, 孙宗辉, 李辉. 热处理对含Mo轴承钢组织和性能的影响[J]. 金属热处理, 2022, 47(7): 125-128.
[11]	匡成阳, 马煜林, 王辰昱, 何家勇, 鲁坤. 回火温度对耐热钢组织和性能的影响[J]. 金属热处理, 2022, 47(7): 129-133.
[12]	殷剑, 金康, 黎诚, 董奇, 沈智, 张波. 时效处理对7022铝合金组织与弯曲性能的影响[J]. 金属热处理, 2022, 47(7): 144-150.
[13]	张凯, 张建平, 钟宁, 卢尚文. 淬火回火工艺对Cr26过共晶高铬铸铁组织及性能的影响[J]. 金属热处理, 2022, 47(7): 156-162.
[14]	董彦超, 马铁军, 金头男, 袁乃博, 金头男. 含铝高硼高速钢显微组织的电镜表征[J]. 金属热处理, 2022, 47(7): 177-182.
[15]	王英虎. 基于FactSage的Fe-15Mn-8Al-0.25C低密度钢的组织及力学性能[J]. 金属热处理, 2022, 47(7): 203-210.