Nb对高Ti耐候钢连续冷却后显微组织及硬度的影响

doi:10.13251/j.issn.0254-6051.2022.08.007

金属热处理 ›› 2022, Vol. 47 ›› Issue (8): 46-51.DOI: 10.13251/j.issn.0254-6051.2022.08.007

Nb对高Ti耐候钢连续冷却后显微组织及硬度的影响

何博¹, 彭天恩², 胡学文¹, 蒋波², 郭锐¹, 石践¹, 汪飞¹, 王海波¹

1.马鞍山钢铁股份有限公司技术中心, 安徽马鞍山 243000;
2.北京科技大学材料科学与工程学院, 北京 100083

收稿日期:2022-03-25 修回日期:2022-06-15 出版日期:2022-08-25 发布日期:2022-09-19
作者简介:何博(1986—),男,工程师,硕士,主要研究方向为耐腐蚀钢材料,E-mail:hebo2005@126.com。

Effect of Nb on microstructure and hardness of high Ti weathering steel after continuous cooling

He Bo¹, Peng Tianen², Hu Xuewen¹, Jiang Bo², Guo Rui¹, Shi Jian¹, Wang Fei¹, Wang Haibo¹

1. Technology Center, Maanshan Iron & Steel Co., Ltd., Maanshan Anhui 243000, China;
2. School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China

Received:2022-03-25 Revised:2022-06-15 Online:2022-08-25 Published:2022-09-19

摘要/Abstract

摘要： 采用Gleeble热模拟试验机研究了微合金元素Nb对高Ti耐候钢奥氏体连续冷却转变行为的影响,通过光学显微镜(OM)、透射电镜(TEM)以及硬度测试等手段比较了0.050%Nb和无Nb试验钢连续冷却转变后显微组织和硬度的变化。结果表明,Nb能抑制铁素体相变,促进贝氏体相变。冷却速度由5 ℃/s提高到10 ℃/s,两种试验钢的晶粒细化效果均最显著,无Nb钢和0.050%Nb钢硬度分别增加了22 HV0.2和25 HV0.2。冷却速度为40 ℃/s时,无Nb试验钢中析出物主要为6～13 nm球形Ti(C, N)复合析出物;含Nb试验钢中主要为5～12 nm球形(Ti, Nb)(C, N)和10～15 nm方形(Ti, Nb)(C, N)复合析出物,含Nb试验钢析出物较多,因此析出强化作用更强。在高Ti耐候钢中,Nb产生的晶粒细化作用并不显著。在相同冷速下,0.050%Nb试验钢的硬度略高于无Nb试验钢,最大差值仅为11 HV0.2。

关键词: Nb, 耐候钢, 连续冷却, 显微组织, 硬度

Abstract: Effect of Nb on continuous cooling transformation behavior of the high Ti weathering steel was studied by Gleeble thermal simulation testing machine. Microstructure and hardness of the tested steel without Nb addition and that added 0.050% Nb after continuous cooling transformation were observed and analyzed by optical microscope (OM), transmission electron microscope (TEM) and hardness test. The results show that Nb can inhibit ferrite transformation and promote bainite transformation. When the cooling rate increases from 5 ℃/s to 10 ℃/s, the grain refinement effect of the two tested steels is the most significant, and the hardness of the steels without and with Nb addition increases by 22 HV0.2 and 25 HV0.2, respectively. When the cooling rate is 40 ℃/s, the precipitate in the steel without Nb is mainly 6-13 nm spherical Ti(C,N), while the precipitates in the 0.050% Nb-microalloyed steel are mainly 5-12 nm spherical (Ti,Nb) (C,N) and 10-15 nm square (Ti,Nb) (C,N). The amount of precipitates in 0.050% Nb-microalloyed steel is more, so the precipitation strengthening effect is more significant. The effect of Nb on grain refinement is not significant in the high Ti weathering steel. The hardness of 0.050%Nb-microalloyed steel is only slightly higher than that of the steel without Nb at the same cooling rate, the maximum difference is only 11 HV0.2.

Key words: Nb, weathering steel, continuous cooling, microstructure, hardness

中图分类号:

TG142.1

何博, 彭天恩, 胡学文, 蒋波, 郭锐, 石践, 汪飞, 王海波. Nb对高Ti耐候钢连续冷却后显微组织及硬度的影响[J]. 金属热处理, 2022, 47(8): 46-51.

He Bo, Peng Tianen, Hu Xuewen, Jiang Bo, Guo Rui, Shi Jian, Wang Fei, Wang Haibo. Effect of Nb on microstructure and hardness of high Ti weathering steel after continuous cooling[J]. Heat Treatment of Metals, 2022, 47(8): 46-51.

参考文献

[1]郑凯锋, 张宇, 衡俊霖, 等. 高强度耐候钢及其在桥梁中的应用与前景[J]. 哈尔滨工业大学学报, 2020, 52(3): 7-16.
Zheng Kaifeng, Zhang Yu, Heng Junlin, et al. High strength weathering steel and its application and prospect in bridge engineering[J]. Journal of Harbin Institute of Technology, 2020, 52(3): 7-16.
[2]Morcillo M, Díaz I, Cano H, et al. Atmospheric corrosion of weathering steels. Overview for engineers. Part I: Basic concepts[J]. Construction and Building Materials, 2019, 213: 723-737.
[3]刘晓翠, 张转转, 刘锟, 等. Cu、Cr、Ni元素对高强耐候钢腐蚀稳定性的影响[J]. 轧钢, 2019, 36(6): 17-21.
Liu Xiaocui, Zhang Zhuanzhuan, Liu Kun, et al. Influence of copper, chromium and nickel on the corrosion resistance property of high strength weathering resistant steel[J]. Steel Rolling, 2019, 36(6):17-21.
[4]于千. 耐候钢发展现状及展望[J]. 钢铁研究学报, 2007, 19(11): 1-4.
Yu Qian. Review and prospect of weathering steel[J]. Journal of Iron and Steel Research, 2007, 19(11): 1-4.
[5]赵培林, 孙新军, 汤化胜, 等. Nb微合金化对热轧700 MPa超高强耐候钢组织和性能的影响[J]. 特殊钢, 2012, 33(1): 46-50.
Zhao Peilin, Sun Xinjun, Tang Huasheng, et al. Effect of Nb microalloying on structure and properties of hot-rolled 700 MPa super-high strength weathering steel[J]. Special Steel, 2012, 33(1): 46-50.
[6]Gan Xiaolong, Xu Guang, Zhao Gang, et al. Composition optimization of Nb-Ti microalloyed high strength steel[J]. Journal of Wuhan University of Technology(Materials Science Edition), 2018, 33(5): 1193-1197.
[7]Sun M Y, Wang X L, Wang X M. Effect of Nb on microstructure and mechanical properties of 700 MPa grade truck beam steel[J]. Kovovematerialy, 2020, 58(5): 351-361.
[8]王晓南, 杜林秀, 张海仑, 等. 780 MPa级重载汽车用大梁钢的工业试制[J]. 钢铁研究学报, 2011, 23(5): 45-49.
Wang Xiaonan, Du Linxiu, Zhang Hailun, et al. Industrial trial of 780 MPa grade heavy-duty truck beams steels[J]. Journal of Iron and Steel Research, 2011, 23(5): 45-49.
[9]Pavlina E, Van T C J. Correlation of yield strength and tensile strength with hardness for steels[J]. Journal of Materials Engineering and Performance, 2008, 17(6): 888-893.
[10]Pickering F B. Physical Metallurgy and the Design of Steels[M]. London: Applied Science Publishers, 1978: 63.
[11]Cancio María José, Echaniz Guillermo, Pérez Teresa Estela. Characterisation of microalloy precipitates in the austenitic range of high strength low alloy steels[J]. Steel Research, 2002, 73(8): 340-346.
[12]Petch N J. The cleavage strength of polycrystals[J]. Journal of the Iron and Steel Institute, 1953, 174(1): 25-28.
[13]乔立峰, 张红梅, 王渐灵, 等. 细晶高强IF钢连续冷却相变的研究[J]. 热加工工艺, 2008, 37(16): 50-52.
Qiao Lifeng, Zhang Hongmei, Wang Jianling, et al. Study on continuous cooling transformation of fine-grain and high strength IF steel[J]. Hot Working Technology, 2008, 37(16): 50-52.
[14]陆阳, 郭占成, 高金涛, 等. 轧制水冷速度对Ti微合金钢中纳米碳化物及其强化作用的影响[J]. 有色金属科学与工程, 2016, 7(6): 56-61.
Lu Yang, Guo Zhancheng, Gao Jintao, et al. Effect of rolling water cooling rate on nano-carbide precipitates and precipitation strengthening of Ti microalloyed steel[J]. Nonferrous Metals Science and Engineering, 2016, 7(6): 56-61.
[15]于庆波, 段贵生, 孙莹, 等. 粒状贝氏体组织对低碳钢力学性能的影响[J]. 钢铁, 2008, 43(7): 68-71.
Yu Qingbo, Duan Guisheng, Sun Ying, et al. Effect of granular bainite on mechanical properties of low-carbon steel[J].Iron and Steel, 2008, 43(7): 68-71.
[16]任家宽, 吴思炜, 陈其源, 等. Ti含量对低碳钢力学性能的影响[J]. 金属热处理, 2017, 42(6): 137-141.
Ren Jiakuan, Wu Siwei, Chen Qiyuan, et al. Influence of Ti content on mechanical properties of low carbon steel[J]. Heat Treatment of Metals, 2017, 42(6): 137-141.
[17]Gladman T. Precipitation hardening in metals[J]. Materials Science and Technology, 1999, 15(1): 30-36.
[18]G#xF6;tz G, Blum W. Influence of thermal history on precipitation of hardening phases in tempered martensite 10%Cr-steel X12CrMoWVNbN 10-1-1[J]. Materials Science and Engineering A, 2003, 348(1): 201-207.
[19]霍向东, 毛新平, 董锋. 卷取温度对Ti微合金化高强钢力学性能的影响机理[J]. 北京科技大学学报, 2013, 35(11): 1472-1477.
Huo Xiangdong, Mao Xinping, Dong Feng. Effect of coiling temperature on the mechanical properties of Ti-microalloyed high strength steel[J]. Journal of University of Science and Technology Beijing, 2013, 35(11): 1472-1477.
[20]王东. 钛微合金化钢中钛与非金属元素相互作用基础研究[D]. 昆明: 昆明理工大学, 2013.

Nb对高Ti耐候钢连续冷却后显微组织及硬度的影响

Effect of Nb on microstructure and hardness of high Ti weathering steel after continuous cooling

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	周丽娜, 刘明, 高翔, 王文雪, 童锐. 奥氏体化过程对Cr14Mo4V高温轴承钢微观组织的影响[J]. 金属热处理, 2022, 47(8): 7-15.
[2]	许峰, 陈前, 林芷民, 成浩, 管怡杰, 陆凯健. Nb和Mo对矿用磨球用钢微结构和相变的影响[J]. 金属热处理, 2022, 47(8): 52-57.
[3]	秦铁玉, 宋春燕, 马汝成, 张学峰, 郝威, 贵永亮. Si含量对Fe-Cr-Si系合金组织与耐蚀性能的影响[J]. 金属热处理, 2022, 47(8): 77-82.
[4]	张明玉, 运新兵, 伏洪旺. 热处理冷却方式对TC10钛合金组织与性能的影响[J]. 金属热处理, 2022, 47(8): 98-104.
[5]	彭龙生, 林英华, 黄伟, 陈皓. 感应淬火对Cr12MoV钢轧辊硬度和硬化层深度的影响[J]. 金属热处理, 2022, 47(8): 118-122.
[6]	陈俭兰, 赵莫迪, 韩福生. 退火对冷轧Cu-Ag合金组织及性能的影响[J]. 金属热处理, 2022, 47(8): 129-134.
[7]	魏海霞, 潘吉祥, 纪显斌, 李照国, 徐斌. 热处理对经济型高碳马氏体不锈钢J50Cr13组织和硬度的影响[J]. 金属热处理, 2022, 47(8): 148-151.
[8]	石向东, 李德贵, 曹阿林, 古斌, 梁柳青. 热处理温度对Al-Gd合金凝固组织和硬度的影响[J]. 金属热处理, 2022, 47(8): 182-187.
[9]	李向川, 杨吉春, 白国君, 樊志明. 热处理对U76CrRE稀土重轨钢夹杂物和微观组织的影响[J]. 金属热处理, 2022, 47(8): 200-210.
[10]	田春英, 董纪, 王军, 张慧星, 冯天建, 刘晓凡. 淬火温度对5Cr15MoV钢空冷淬火组织与性能的影响[J]. 金属热处理, 2022, 47(8): 211-216.
[11]	朱德荣, 李豪, 柳翊, 王利鸽, 陈智勇, 张慧贤, 梁莉. 固溶时效对SLM成形316L不锈钢块体件显微组织及硬度的影响[J]. 金属热处理, 2022, 47(8): 237-241.
[12]	刘港, 刘静, 杨峰, 向庆. 钛合金化学热处理研究进展[J]. 金属热处理, 2022, 47(8): 249-256.
[13]	杨来侠, 李佳乐, 徐超, 杨文选. 扫描速度对激光沉积ER630丝材修复层力学性能与显微组织的影响[J]. 金属热处理, 2022, 47(8): 271-278.
[14]	魏永强, 顾艳阳, 赵重轻, 蒋志强. 脉冲偏压占空比对TiSiN薄膜结构和性能的影响[J]. 金属热处理, 2022, 47(8): 279-286.
[15]	牛毅, 贺占胥, 王明利, 张杰, 牛文朋, 刘贯军. 离子渗氮对304不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(8): 287-291.