Nb和Mo对矿用磨球用钢微结构和相变的影响

doi:10.13251/j.issn.0254-6051.2022.08.008

金属热处理 ›› 2022, Vol. 47 ›› Issue (8): 52-57.DOI: 10.13251/j.issn.0254-6051.2022.08.008

Nb和Mo对矿用磨球用钢微结构和相变的影响

许峰¹, 陈前¹, 林芷民¹, 成浩¹, 管怡杰¹, 陆凯健²

1.常熟理工学院汽车工程学院, 江苏常熟 215500;
2.苏州大学机电工程学院, 江苏苏州 215021

收稿日期:2022-03-12 修回日期:2022-06-13 出版日期:2022-08-25 发布日期:2022-09-19
作者简介:许峰(1982—),男,高级工程师,博士,主要研究方向为金属形变微结构和织构演变及搅拌摩擦加工技术,E-mail:xufeng388@163.com。

Effect of Nb and Mo on microstructure and phase transformation of steel for mining grinding balls

Xu Feng¹, Chen Qian¹, Lin Zhimin¹, Cheng Hao¹, Guan Yijie¹, Lu Kaijian²

1. School of Automotive Engineering, Changshu Institute of Technology, Changshu Jiangsu 215500, China;
2. School of Mechanical and Electrical Engineering, Soochow University, Suzhou Jiangsu 215021, China

Received:2022-03-12 Revised:2022-06-13 Online:2022-08-25 Published:2022-09-19

摘要/Abstract

摘要： 对不同合金成分磨球用钢样品进行高温激光共聚焦显微镜(HT-CLSM)原位观察和JMatPro软件模拟计算,研究了Nb、Mo元素对其热处理过程中微结构和相变的影响。结果表明,试验钢中添加0.051%Nb元素的原奥氏体平均晶粒尺寸最小(38.8 μm),添加0.079%Mo元素的次之,无添加的最大,可达74.1 μm。添加Nb元素时,析出物类别主要为Nb(C, N)和MnS,析出物的数量最多,显著阻碍了高温奥氏体晶粒长大。添加Mo元素时,析出物类别主要为MnS和AlN,析出物数量次之,对奥氏体晶粒长大有一定的阻碍作用。Nb和Mo元素的添加均有利于扩大贝氏体转变区,增加贝氏体转变量,提高马氏体转变开始温度。

关键词: 磨球钢, Nb, Mo, 微结构, 相变

Abstract: Effect of Nb and Mo on microstructure and phase transformation of grinding ball steel with different alloy composition during heat treatment was studied by using high temperature confocal laser scanning microscope (HT-CLSM) and JMatPro simulation calculation. The results show that the average austenite grain size of the tested steel with 0.051%Nb is the smallest (38.8 μm), that without Nb or Mo addition is the largest (74.1 μm), and that with 0.079% Mo is the intermediate. With Nb element addition, the precipitates are mainly Nb(C, N) and MnS, and the amount of precipitates is the most, which significantly hinder the grain growth of high temperature austenite. While with Mo element addition, the precipitates are mainly MnS and AlN, and the amount of precipitates is the intermediate, which slightly hinder the grain growth of austenite. The addition of Nb and Mo is beneficial to expand the bainite transformation zone, increases the percentage of bainite transformation and increases the martensite transformation start temperature.

Key words: grinding ball steel, Nb, Mo, microstructure, phase transformation

中图分类号:

TG161

许峰, 陈前, 林芷民, 成浩, 管怡杰, 陆凯健. Nb和Mo对矿用磨球用钢微结构和相变的影响[J]. 金属热处理, 2022, 47(8): 52-57.

Xu Feng, Chen Qian, Lin Zhimin, Cheng Hao, Guan Yijie, Lu Kaijian. Effect of Nb and Mo on microstructure and phase transformation of steel for mining grinding balls[J]. Heat Treatment of Metals, 2022, 47(8): 52-57.

参考文献

[1]杨业元, 方鸿生, 姜忠良, 等. 国外耐磨钢球质量评析[J]. 矿山机械, 1993(10): 22-25.
Yang Yeyuan, Fang Hongsheng, Jiang Zhongliang, et al. Quality evaluation of foreign wear-resistant steel balls[J]. Mining and Processing Equipment, 1993(10): 22-25.
[2]白雪, 金云学. 大型球磨机用耐磨钢球的热处理[J]. 金属热处理, 2017, 42(5): 193-196.
Bai Xue, Jin Yunxue. Heat treatment of wear resistant steel ball for large ball mill[J]. Heat Treatment of Metals, 2017, 42(5): 193-196.
[3]高丽梅, 侯建民, 梁柱, 等. 大直径锻造耐磨钢球的热处理工艺[J]. 金属热处理, 2021, 46(2): 153-156.
Gao Limei, Hou Jianmin, Liang Zhu, et al. Heat treatment process of large diameter forged wear-resistant steel ball[J]. Heat Treatment of Metals, 2021, 46(2): 153-156.
[4]董登超, 张珂, 吴园园, 等. 耐磨钢球落球试验开裂原因分析[J]. 金属热处理, 2017, 42(4): 200-203.
Dong Dengchao, Zhang Ke, Wu Yuanyuan, et al. Cracking analysis of wearable steel ball during ball falling test[J]. Heat Treatment of Metals, 2017, 42(4): 200-203.
[5]方鸿生, 郑燕康, 黄进峰. 锰-硼系空冷贝氏体钢的新近发展[J]. 金属热处理, 1997, 22(4): 9-12.
Fang Hongsheng, Zheng Yankang, Huang Jinfeng. Recent development of Mn-B system air cooled bainitic steels[J]. Heat Treatment of Metals, 1997, 22(4): 9-12.
[6]李凤照, 敖青, 姜江, 等. 超细组织空冷贝氏体钢[J]. 金属热处理, 1998, 23(1): 5-7.
Li Fengzhao, Ao Qing, Jiang Jiang, et al. Ultrafine structure bainitic steels[J]. Heat Treatment of Metals, 1998, 23(1): 5-7.
[7]包喜荣, 王均安, 王晓东, 等. 一种Mn-Cr-Mo-La系空冷贝氏体钢轨用钢的试验研究[J]. 铁道学报, 2017, 39(4): 118-125.
Bao Xirong, Wang Jun'an, Wang Xiaodong, et al. Study on a Mn-Cr-Mo-La air-cooled bainitic steel for rails[J]. Journal of the China Railway Society, 2017, 39(4): 118-125.
[8]吉光, 高秀华, 龙金花, 等. 矿用耐磨钢球冲击疲劳强度偏低原因分析[J]. 钢铁研究学报, 2017, 29(6): 500-505.
Ji Guang, Gao Xiuhua, Long Jinhua, et al. Analysis of low impact fatigue strength in grinding balls for mining[J]. Journal of Iron and Steel Research, 2017, 29(6): 500-505.
[9]吉光, 高秀华, 龙金花. 微合金元素Nb对B5钢力学性能和微观组织的影响[J]. 材料热处理学报, 2021, 42(4): 102-108.
Ji Guang, Gao Xiuhua, Long Jinhua. Effect of microalloying element Nb on mechanical properties and microstructure of B5 steel[J]. Transactions of Materials and Heat Treatment, 2021, 42(4): 102-108.
[10]李小琳, 王昭东. 含Nb-Ti低碳微合金钢纳米碳化物析出行为[J]. 东北大学学报(自然科学版), 2015, 36(12): 1701-1705.
Li Xiaolin, Wang Zhaodong. Precipitation behaviors of nanometer-sized carbides in a niobium-titanium contained low-carbon steel[J]. Journal of Northeastern University(Natural Science), 2015, 36(12): 1701-1705.
[11]屈天鹏, 王德永, 徐周, 等. 含Nb-Ti微合金钢连铸过程中TiN析出行为研究[J]. 连铸, 2017, 42(2): 32-38.
Qu Tianpeng, Wang Deyong, Xu Zhou, et al. Precipitation behavior of TiN in Nb-Ti alloyed steel during continuous casting process[J]. Continuous Casting, 2017, 42(2): 32-38.
[12]何仙灵, 杨庚蔚, 毛新平, 等. Nb对Ti-Mo微合金钢连续冷却相变规律及组织性能的影响[J]. 金属学报, 2017, 53(6): 648-656.
He Xianling, Yang Gengwei, Mao Xinping, et al. Effect of Nb on the continuous cooling transformation rule and microstructure, mechanical properties of Ti-Mo bearing microalloyed steel[J]. Acta Metallurgica Sinica, 2017, 53(6): 648-656.
[13]Mao X P, Chen Q L, Sun X J. Metallurgical interpretation on grain refinement and synergistic effect of Mn and Ti in Ti-microalloyed strip produced by TSCR[J]. Journal of Iron Steel Research (International), 2014, 21(1): 30-40.
[14]聂文金, 尚成嘉, 吴圣杰, 等. Nb对奥氏体热变形后等温回复的影响[J]. 金属学报, 2012, 48(7): 775-781.
Nie Wenjin, Shang Chengjia, Wu Shengjie, et al. Effects of Nb on recovery of hot-deformed austenite[J]. Acta Metallurgica Sinica, 2012, 48(7): 775-781.

[1]	张铮, 陈进磊, 张敏, 乔珺威. 热变形对塑料模具钢SDFT600贝氏体相变的影响[J]. 金属热处理, 2022, 47(8): 1-6.
[2]	周丽娜, 刘明, 高翔, 王文雪, 童锐. 奥氏体化过程对Cr14Mo4V高温轴承钢微观组织的影响[J]. 金属热处理, 2022, 47(8): 7-15.
[3]	何博, 彭天恩, 胡学文, 蒋波, 郭锐, 石践, 汪飞, 王海波. Nb对高Ti耐候钢连续冷却后显微组织及硬度的影响[J]. 金属热处理, 2022, 47(8): 46-51.
[4]	彭龙生, 林英华, 黄伟, 陈皓. 感应淬火对Cr12MoV钢轧辊硬度和硬化层深度的影响[J]. 金属热处理, 2022, 47(8): 118-122.
[5]	冯凌宵, 金浩, 杨丽. PCrNi3Mo钢真空渗铬层的组织与性能[J]. 金属热处理, 2022, 47(8): 168-172.
[6]	田春英, 董纪, 王军, 张慧星, 冯天建, 刘晓凡. 淬火温度对5Cr15MoV钢空冷淬火组织与性能的影响[J]. 金属热处理, 2022, 47(8): 211-216.
[7]	廖佳, 付涛, 王晓巍, 余胜峰, 王瑞麒, 彭飞. 回火温度对大尺寸锻态35CrMo钢微观组织和力学性能的影响[J]. 金属热处理, 2022, 47(8): 232-236.
[8]	金玉亮, 刘春江, 吴彬龙, 张洪亮. 40CrNiMoA钢传动轴花键开裂失效分析[J]. 金属热处理, 2022, 47(8): 296-300.
[9]	韩俊刚, 邵志文, 宋运坤, 陈小虎, 丁博远, 顾娇娇. 热处理对针阀体用4Cr5MoSiV1钢组织及性能的影响[J]. 金属热处理, 2022, 47(7): 120-124.
[10]	许荣昌, 王毅, 孙宗辉, 李辉. 热处理对含Mo轴承钢组织和性能的影响[J]. 金属热处理, 2022, 47(7): 125-128.
[11]	王英虎. 基于FactSage的Fe-15Mn-8Al-0.25C低密度钢的组织及力学性能[J]. 金属热处理, 2022, 47(7): 203-210.
[12]	陈佳俊, 朱治愿, 李建强, 王守乾. 固溶处理对Cr23Ni7Mo2Cu0.6双相不锈钢组织与性能的影响[J]. 金属热处理, 2022, 47(6): 59-63.
[13]	钟彬, 陈义庆, 李琳, 高鹏, 伞宏宇, 艾芳芳, 田秀梅. 淬火油温对40CrMnMo钢钻杆组织和性能的影响[J]. 金属热处理, 2022, 47(6): 98-102.
[14]	杨小禹, 李笑笑, 佟静, 胡树凯. 高压热处理对35CrMo钢组织与硬度的影响[J]. 金属热处理, 2022, 47(6): 119-122.
[15]	吴轲源, 刘云鹏, 李孔斋, 徐良乐. 17-4PH不锈钢连续冷却转变及相变动力学[J]. 金属热处理, 2022, 47(6): 161-167.

Nb和Mo对矿用磨球用钢微结构和相变的影响

Effect of Nb and Mo on microstructure and phase transformation of steel for mining grinding balls

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价