回火温度对30Cr3Si2NiMoWNb钢组织性能的影响

doi:10.13251/j.issn.0254-6051.2022.11.016

金属热处理 ›› 2022, Vol. 47 ›› Issue (11): 95-99.DOI: 10.13251/j.issn.0254-6051.2022.11.016

回火温度对30Cr3Si2NiMoWNb钢组织性能的影响

宁静¹, 杨鹏², 高齐¹, 苏杰¹

1.钢铁研究总院有限公司特殊钢研究院, 北京 100081;
2.大冶特殊钢有限公司特冶产品研究所, 湖北黄石 435001

收稿日期:2022-07-25 修回日期:2022-09-27 出版日期:2022-11-25 发布日期:2023-01-04
通讯作者: 苏杰,正高级工程师,E-mail:sujie@nercast.com
作者简介:宁静(1988—),女,高级工程师,主要研究方向为超高强度钢强韧化,E-mail:ningjing@nercast.com。

Effect of tempering temperature on microstructure and properties of 30Cr3Si2NiMoWNb steel

Ning Jing¹, Yang Peng², Gao Qi¹, Su Jie¹

1. Institute for Special Steels, Central Iron and Steel Research Institute, Beijing 100081, China;
2. Special Metallurgical Products Research Institute, Daye Special Steel Co., Ltd., Huangshi Hubei 435001, China

Received:2022-07-25 Revised:2022-09-27 Online:2022-11-25 Published:2023-01-04

摘要/Abstract

摘要： 采用扫描电镜、能谱分析和力学试验等研究了回火温度对30Cr3Si2NiMoWNb超高强度钢组织和性能的影响。结果表明,回火温度变化可实现对力学性能的大幅度调控。200~350 ℃回火,微观组织为回火马氏体与细小弥散的ε-碳化物,此阶段强韧性变化幅度较小,抗拉强度等级1700 MPa、屈服强度等级1300 MPa;350~500 ℃回火由于渗碳体的不均匀析出,强度和韧性同时下降,其中500 ℃左右回火脆性最为严重,冲击吸收能量下降至最低点;500~700 ℃回火生成较稳定的球状渗碳体,强度大幅下降,韧性大幅上升。回火温度对强韧性的影响机理为ε-碳化物、渗碳体等析出相演变过程的影响;一定含量的Si元素可以提高渗碳体形成温度和回火脆性温度。

关键词: 超高强度钢, 回火温度, 力学性能, 渗碳体

Abstract: Effect of tempering temperature on microstructure and properties of 30Cr3Si2NiMoWNb ultra-high strength steel was studied by means of scanning electron microscopy (SEM), energy dispersive spectrometer (EDS) and mechanical test. The resules show that the tempering temperature can greatly affect and regulate the mechanical properties of the steel. When tempered at 200-350 ℃, the microstructure is composed of tempered martensite and fine dispersed ε-carbides. The fluctuation of strength and toughness is small, the tensile strength grade is 1700 MPa, the yield strength grade is 1300 MPa. Due to the inhomogeneous precipitation of cementite when tempered at 350-500 ℃, the strength and toughness decrease at the same time, and the brittleness is the most serious at about 500 ℃, with impact absorbed energy decreasing to the lowest point. When tempered at 500-700 ℃, stable spherical cementite is formed, and strength decreases and toughness increases greatly. The influence mechanism of tempering temperature on strength and toughness is the evolution process of precipitates such as ε-carbide and cementite. Certain amount of Si can raise the forming temperature of cementite and temper brittleness temperature of the steel.

Key words: ultra-high strength steel, tempering temperature, mechanical properties, cementite

中图分类号:

TG135.1

宁静, 杨鹏, 高齐, 苏杰. 回火温度对30Cr3Si2NiMoWNb钢组织性能的影响[J]. 金属热处理, 2022, 47(11): 95-99.

Ning Jing, Yang Peng, Gao Qi, Su Jie. Effect of tempering temperature on microstructure and properties of 30Cr3Si2NiMoWNb steel[J]. Heat Treatment of Metals, 2022, 47(11): 95-99.

参考文献

[1]万翛如, 许昌淦. 高强度及超高强度钢[M]. 北京: 机械工业出版社, 1988: 2.
[2]罗海文, 沈国慧. 超高强高韧化钢的研究进展和展望[J]. 金属学报, 2020, 56(4): 494-512.
Luo Haiwen, Shen Guohui. Progress and perspective of ultra-high strength steels having high toughness[J]. Acta Metallurgica Sinica, 2020, 56(4): 494-512.
[3]Saeidi N, Ekrami A. Microstructure-toughness relationship in AISI4340 steel[J]. Defect and Diffusion Forum, 2011, 312-315: 110-115.
[4]Youngblood J L, Raghavan M. Correlation of microstructure with mechanical properties of 300m steel[J]. Metallurgical Transactions A, 1977, 8(9): 1439-1448.
[5]赵博, 许广兴, 贺飞, 等. 飞机起落架用超高强度钢应用现状及展望[J]. 航空材料学报, 2017, 37(6): 1-6.
Zhao Bo, Xu Guangxing, He Fei, et al. Present status and prospect of ultra high strength steel applied to aircraft landing gear[J]. Journal of Aeronautical Materials, 2017, 37(6): 1-6.
[6]Totten G E. Steel Heat Treatment: Metallurgy and Technologies (Second Edition)[M]. Boca Raton: CRC Press, 2006.
[7]王立军, 蔡庆伍, 余伟, 等. 1500 MPa级低合金超高强钢的微观组织与力学性能[J]. 金属学报, 2010, 46(6): 687-694.
Wang Lijun, Cai Qingwu, Yu Wei, et al. Microstructure and mechanical properties of 1500 MPa grade ultra-high strength low alloy steel[J]. Acta Metallurgica Sinica, 2010, 46(6): 687-694.
[8]Morris Dilmore, James D R. Eglin steel—A low alloy high strength composition: US, 7537727 B2[P]. 2009-5-26.
[9]王浩楠, 闫晋文, 李顺强, 等. 回火工艺对40CrNiMo 钢组织与性能的影响[J]. 南京理工大学学报, 2022, 46(3): 367-372.
Wang Haonan, Yan Jinwen, Li Shunqiang, et al. Effect of tempering on microstructure and mechanical properties of 40CrNiMo steel[J]. Journal of Nanjing University of Science and Technology, 2022, 46(3): 367-372.
[10]王金海, 郭涛. 淬回火工艺对30CrNi2MoV钢组织与力学性能的影响[J]. 热加工工艺, 2022, 51(20): 152-156.
Wang Jinhai, Guo Tao. Effects of quenching and tempering process on microstructure and mechanical properties of 30CrNi2MoV steel[J]. Hot Working Technology, 2022, 51(20): 152-156.
[11]郑东升, 刘丹, 罗登, 等. 回火温度对超高强钢微观组织及力学性能的影响[J]. 材料热处理学报, 2020, 41(12): 90-96.
Zheng Dongsheng, Liu Dan, Luo Deng, et al. Effect of tempering temperature on microstructure and mechanical properties of ultra-high strength steel[J]. Transactions of Materials and Heat Treatment, 2020, 41(12): 90-96.
[12]刘宪民, 花峰, 刘蕤, 等. 热处理对30CrMnSiNi2A钢力学性能的影响[J]. 钢铁, 2003, 38(1): 43-47.
Liu Xianmin, Hua Feng, Liu Rui, et al. Effect of heat treatment on the mechanical properties of steel 30CrMnSiNi2A[J]. Iron and Steel, 2003, 38(1): 43-47.
[13]王春旭, 厉勇, 韩顺, 等. 高韧性易旋压易焊接超高强度D506A钢及制备方法: CN, 104328359 A[P]. 2015-02-04.
[14]范新超, 王春旭, 厉勇, 等. 回火温度对超高强度35Cr3Ni2SiMnMoVA 钢组织与性能的影响[J]. 金属热处理, 2017, 42(4): 95-98.
Fan Xinchao, Wang Chunxu, Li Yong, et al. Effect of tempering temperature on microstructure and mechanical properties of ultra high strength 35Cr3Ni2SiMnMoVA steel[J]. Heat Treatment of Metals, 2017, 42(4): 95-98.
[15]彭雯雯, 曾卫东, 康超, 等. 热处理工艺对300M 超高强度钢组织和性能的影响[J]. 材料热处理学报, 2012, 33(3): 94-98.
Peng Wenwen, Zeng Weidong, Kang Chao, et al. Effect of heat treatment on microstructure and properties of 300M ultrahigh strength steel[J]. Transactions of Materials and Heat Treatment, 2012, 33(3): 94-98.
[16]王丙旭, 崔威威, 张宇, 等. 回火温度对300M 钢组织和性能的影响[J]. 铸造技术, 2021, 42(8): 719-721.
Wang Bingxu, Cui Weiwei, Zhang Yu, et al. Effect of tempering temperatures on microstructure and mechanical properties of 300M steel[J]. Foundry Technology, 2021, 42(8): 719-721.
[17]路妍, 王军华, 苏杰, 等. 30Cr3Si2Mn2NiNb钢中未溶相的热力学计算及分析[J]. 材料工程, 2011(9): 1-5.
Lu Yan, Wang Junhua, Su Jie. et al. Thermodynamic calculation and experimental analysis on undissolved phases of 30Cr3Si2Mn2NiNb steel[J]. Journal of Materials Engineering, 2011(9): 1-5.
[18]宁静, 杨卓越, 苏杰, 等. 固溶温度对30Cr4Si2NiMoWNb超高强度钢力学性能的影响[J]. 钢铁研究学报, 2017, 29(12): 1030-1034.
Ning Jing, Yang Zhuoyue, Su Jie, et al. Influence of solution treatment temperature on mechanical properties of 30Cr4Si2NiMoWNb steel[J]. Journal of Iron and Steel Research, 2017, 29(12): 1030-1034.
[19]Chang Li, Smith G D W. The silicon effect in the tempering of martensite in steels[J]. Le Journal de Physique Colloques, 1984, 45(C9): 397-401.

回火温度对30Cr3Si2NiMoWNb钢组织性能的影响

Effect of tempering temperature on microstructure and properties of 30Cr3Si2NiMoWNb steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王志文, 杨荣东, 黄元春, 李辉. 时效处理对挤压成型2195铝锂合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(9): 6-11.
[2]	高星, 张宁, 丁燕, 蒋波. 热处理时间对激光选区成形TC4钛合金组织及力学性能的影响[J]. 金属热处理, 2022, 47(9): 12-17.
[3]	夏朋昭, 许莹, 蔡艳青, 赵思坛, 娄冰洁. 微波烧结工艺对Ti-Mg复合材料组织和性能的影响[J]. 金属热处理, 2022, 47(9): 18-26.
[4]	李磊, 朱旭军, 张丽, 田福政. 喷丸直径对GH4169合金性能和损伤演化的影响[J]. 金属热处理, 2022, 47(9): 47-53.
[5]	张浩泽, 王隽生, 宫鹏辉, 詹海艺, 王凯. 热处理对EB铸锭直接轧制TC4合金板材组织和力学性能的影响[J]. 金属热处理, 2022, 47(9): 71-78.
[6]	钟立伟, 冯朝辉, 高文理, 陈军洲, 陆政. 多轴锻造与T852热处理对Al-Cu-Li合金组织及力学性能的影响[J]. 金属热处理, 2022, 47(9): 79-86.
[7]	肖结良, 孙浩, 李飞, 胡平, 陈旌钢, 江兆峰. 球墨铸铁行走轮的低温正火工艺[J]. 金属热处理, 2022, 47(9): 98-102.
[8]	温方明, 郝晓博, 曹恒, 张强, 李渤渤, 刘茵琪. 热处理工艺对N06600合金热轧板组织与性能的影响[J]. 金属热处理, 2022, 47(9): 113-118.
[9]	艾兵权, 邝霜, 田秀刚, 杨峰, 王玉慧, 逯志强, 王朝, 郝雷. 均热温度对不同成分980 MPa级高强钢组织和性能的影响[J]. 金属热处理, 2022, 47(9): 119-124.
[10]	王世凯, 王睿, 康燕, 于志强, 闫志杰. 淬火温度对Cr5MoVNi钢组织和性能的影响[J]. 金属热处理, 2022, 47(9): 125-129.
[11]	熊维亮, 梁文, 吴腾, 梁亮, 吴浩鸿. 控冷工艺对热轧双相钢组织与性能的影响[J]. 金属热处理, 2022, 47(9): 130-133.
[12]	张玉成, 贾浩梅. 固溶处理对Incoloy825合金钢管组织和性能的影响[J]. 金属热处理, 2022, 47(9): 134-139.
[13]	范朝, 程宗辉, 张志强. 激光热输入对激光增材修复1Cr17Ni2不锈钢组织与力学性能的影响[J]. 金属热处理, 2022, 47(9): 140-145.
[14]	李颖, 彭霜, 张婷, 柴象海, 翁依柳. 选区激光熔化制备Ti-6Al-4V合金的热处理工艺及力学性能[J]. 金属热处理, 2022, 47(9): 175-181.
[15]	谯德高, 罗晓阳, 胡双喜, 侯园园, 张志坚, 唐兴昌. 280VK冷轧高强钢退火过程的组织演变及析出机理[J]. 金属热处理, 2022, 47(9): 220-226.