30CrMnSiNi2A钢轴类零件感应热处理的数值模拟

doi:10.13251/j.issn.0254-6051.2023.04.037

金属热处理 ›› 2023, Vol. 48 ›› Issue (4): 235-244.DOI: 10.13251/j.issn.0254-6051.2023.04.037

30CrMnSiNi2A钢轴类零件感应热处理的数值模拟

陈素明¹, 杨平¹, 任树锋², 罗贤², 王文博¹

1.中航西安飞机工业集团股份有限公司, 陕西西安 710089;
2.西北工业大学材料学院, 陕西西安 710072

收稿日期:2022-09-23 修回日期:2022-12-26 发布日期:2023-05-27
作者简介:陈素明(1978—)，男，研究员级高级工程师，主要研究方向为航空特种工艺，E-mail:xac＿csm@sina.com

Numerical simulation of induction heat treatment of 30CrMnSiNi2A steel shaft parts

Chen Suming¹, Yang Ping¹, Ren Shufeng², Luo Xian², Wang Wenbo¹

1. AVIC Xi'an Aircraft Industry Group Company Ltd., Xi'an Shaanxi 710089, China;
2. School of Materials Science and Engineering, Northwestern Polytechnical University, Xi'an Shaanxi 710072, China

Received:2022-09-23 Revised:2022-12-26 Published:2023-05-27

摘要/Abstract

摘要： 利用Comsol软件对30CrMnSiNi2A钢的感应回火进行了模拟,利用控制变量法研究了感应加热过程中电源频率、电流以及线圈的结构和尺寸参数对工件内部温度均匀性的影响。结果表明,电流强度和电源频率越大,工件在感应加热过程中的升温速率越大,最终平衡温度越高,但其径向/轴向温差越大。线圈的匝数越多,工件的升温速率和径向/轴向温差越大,最终平衡温度越高。线圈半径的变化仅会对工件端部的升温速率产生影响,线圈半径越小,工件端部的升温速率越快,轴向温差越小。线圈截面外径和壁厚的变化对工件感应加热过程中的温度场没有影响。根据模拟结果的对比分析,提出了一种采用分段加热法与增设导磁体相结合的方法,对感应回火系统进行了优化。通过优化设计可使工件在感应加热过程中的径向温差基本消除,使轴向温差小于10 ℃。

关键词: 30CrMnSiNi2A钢, 感应热处理, 数值模拟, 电源参数, 线圈结构, 温度场

Abstract: Comsol software was used to simulate the induction tempering of 30CrMnSiNi2A steel. The effects of power frequency, current, and structure and size parameter of coil on temperature homogenity in the workpiece during induction heating were studied by using control variable method. The results show that the greater the current intensity and power frequency, the greater the heating rate of the workpiece in the induction heating process, the higher the final balance temperature, but the greater the radial/axial temperature difference. The more turns of the coil, the greater heating rate and radial/axial temperature difference of the workpiece, as well as the higher the final balance temperature. The change of coil radius will only affect the heating rate at the end of the workpiece, the smaller the coil radius, the faster the heating rate at the end of the workpiece, and the smaller the axial temperature difference. The change of coil section outer diameter and wall thickness has no effect on the temperature field of the workpiece during induction heating. According to the comparative analysis of the simulation results, a method of combining sectional heating method with adding magnetic flux concentrator is proposed to optimize the induction tempering system. Through design optimization, it is possible to eliminate the radial temperature difference of the workpiece during induction heating, while also controlls the axial temperature difference to be within 10 ℃.

Key words: 30CrMnSiNi2A steel, induction heat treatment, numerical simulation, power parameters, coil structure, temperature field

中图分类号:

TG156.9

陈素明, 杨平, 任树锋, 罗贤, 王文博. 30CrMnSiNi2A钢轴类零件感应热处理的数值模拟[J]. 金属热处理, 2023, 48(4): 235-244.

Chen Suming, Yang Ping, Ren Shufeng, Luo Xian, Wang Wenbo. Numerical simulation of induction heat treatment of 30CrMnSiNi2A steel shaft parts[J]. Heat Treatment of Metals, 2023, 48(4): 235-244.

参考文献

[1]Shi X H, Zeng W D, Zhao Q Y, et al. Study on the microstructure and mechanical properties of Aermet 100 steel at the tempering temperature around 482 ℃ [J]. Journal of Alloys and Compounds, 2016, 679: 184-190.
[2]Zhang Y P, Zhan D P, Qi X W, et al. Microstructure and mechanical properties of Cr14 ultra-high-strength steel at different tempering temperatures around 773 K [J]. Materials Science and Engineering A, 2017, 698: 152-161.
[3]Niu Q L, Ming W W, Chen M, et al. Dynamic mechanical behavior of ultra-high strength steel 30CrMnSiNi2A at high strain rates and elevated temperatures [J]. Journal of Iron and Steel Research International, 2017, 24(7): 724-729.
[4]陆文杰. 30CrMnSiNi2A螺纹件局部感应回火工艺模拟研究[D]. 南昌: 南昌航空大学, 2017.
Lu Wenjie. Simulation analysis of local induction tempering process of 30CrMnSiNi2A thread parts [D]. Nanchang: Nanchang Hangkong University, 2017.
[5]陆文杰, 华小珍, 周贤良, 等. 感应加热工艺参数对30CrMnSiNi2A钢轴件温度分布的影响[J]. 金属热处理, 2017, 42(8): 187-191.
Lu Wenjie, Hua Xiaozhen, Zhou Xianliang, et al. Effect of induction heating process parameters on temperature distribution of 30CrMnSiNi2A steel shaft [J]. Heat Treatment of Metals, 2017, 42(8): 187-191.
[6]Kenji H, Akihide N, Yutaka M. 550 and 610 MPa class high-strength steel plates with excellent toughness for tanks and penstocks produced using carbide morphology controlling technology [J]. JFE Technical Report, 2008(11): 19-25.
[7]Yu A Samoilovich. Transient and residual stress in rollers quenched after inductive heating [J]. Steel in Translation, 2015, 45(1): 73-79.
[8]张云鹭. 感应热处理工艺数值分析与快速奥氏体化动力学研究[D]. 上海: 上海交通大学, 2013.
Zhang Yunlu. Numerical investigation on induction heat treatment and research on rapid austenization kinetics [D]. Shanghai: Shanghai Jiao Tong University, 2013.
[9]王奇. 伞齿轮双频感应淬火过程数值分析[D]. 秦皇岛: 燕山大学, 2018.
Wang Qi. Numerical analysis of dual frequency induction hardening process of bevel gears [D]. Qinhuangdao: Yanshan University, 2018.
[10]陈庆安, 王艳辉, 张建宇, 等. 钢板连续移动感应淬火温度场数值模拟及实验研究[J]. 表面技术, 2020, 49(9): 332-338.
Chen Qing'an, Wang Yanhui, Zhang Jianyu, et al. Numerical simulation and experiment research on the temperature field of continual induction hardening for a steel plate [J]. Surface Technology, 2020, 49(9): 332-338.
[11]Zabett A, Azghandi S. Simulation of induction tempering process of carbon steel using finite element method [J]. Materials and Design, 2012, 36: 415-420.
[12]杨晨光. 42CrMo钢轴类件变功率感应加热数值模拟研究[D]. 秦皇岛: 燕山大学, 2010.
Yang Chenguang. The 42CrMo steel shaft piece variable power induction heating numerical simulation study [D]. Qinhuangdao: Yanshan University, 2010.

[1]	蒋志鹏, 陈浩, 吴晓春. 压铸模具钢大模块真空高压气淬冷却过程的数值模拟[J]. 金属热处理, 2023, 48(4): 211-220.
[2]	张斌, 尹少武, 张文聪, 卢世杰, 童莉葛, 王立. 富氧燃烧条件下钢坯加热特性的数值模拟[J]. 金属热处理, 2023, 48(4): 221-228.
[3]	王中琳, 李权, 龚志华, 包汉生, 雍兮. 丝杠用1Cr15Ni4Mo2CuN不锈钢热处理温度场的有限元数值模拟[J]. 金属热处理, 2023, 48(4): 245-252.
[4]	王伟, 张文, 赵建森, 朱百智, 米艳军, 江红兵, 胡成飞. 42CrMo钢输出法兰感应淬火的数值模拟及验证[J]. 金属热处理, 2023, 48(2): 242-246.
[5]	王冰涛, 熊宗慧, 孙耀宁. 不锈钢表面激光熔覆镍基合金涂层的数值模拟与试验[J]. 金属热处理, 2023, 48(1): 232-237.
[6]	袁丽, 贺笃鹏, 何欣, 秦湘阁. 16Cr3NiWMoVNbE钢C型环真空低压渗碳及淬火有限元模拟[J]. 金属热处理, 2022, 47(9): 257-263.
[7]	王志敏, 黄春玲, 曹宇鹏. 激光冲击波传播特性对E690钢表面微凹坑动态塑性变形的影响[J]. 金属热处理, 2022, 47(6): 253-258.
[8]	熊梨, 张登春, 宋石初, 陈霖. 碳化硅真空烧结炉温度场数值模拟与系统优化[J]. 金属热处理, 2022, 47(6): 259-265.
[9]	郭硕, 樊振宇, 王会珍, 周乐育, 翟月雯. H13钢相变规律及其模具的真空热处理数值模拟[J]. 金属热处理, 2022, 47(5): 71-75.
[10]	唐梦兰, 吴仡璇, 仝大明, 顾剑锋. 9310钢螺旋锥齿轮模压淬火的数值模拟[J]. 金属热处理, 2022, 47(5): 234-240.
[11]	赵欣, 陈正宗, 赵海平. 马氏体耐热钢大型管坯加热工艺模拟[J]. 金属热处理, 2022, 47(4): 208-212.
[12]	杨杰, 汪西, 周杰, 武建祥, 屈志远, 代合平, 彭海军. 转向节锻件枝丫结构淬火裂纹形成机理[J]. 金属热处理, 2022, 47(4): 263-267.
[13]	蔡显杰, 吴博雅, 左鹏鹏, 黎军顽, 郭伟. 压铸模镶块的热疲劳失效行为[J]. 金属热处理, 2022, 47(2): 250-256.
[14]	王皓, 王婧, 徐骏, 顾剑锋, 郭正洪. 基于多场耦合模拟的齿毂高压气淬工艺设计[J]. 金属热处理, 2022, 47(12): 244-251.
[15]	强菲, 王文, 张婷, 杨娟, 蔡军, 王快社. Al-Zn-Mg-Cu铝合金厚板搅拌摩擦焊接头搅拌区微观组织[J]. 金属热处理, 2022, 47(1): 135-141.

30CrMnSiNi2A钢轴类零件感应热处理的数值模拟

Numerical simulation of induction heat treatment of 30CrMnSiNi2A steel shaft parts

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价