高温时效对G115钢蠕变-疲劳裂纹扩展行为的影响

doi:10.13251/j.issn.0254-6051.2023.07.005

金属热处理 ›› 2023, Vol. 48 ›› Issue (7): 26-31.DOI: 10.13251/j.issn.0254-6051.2023.07.005

高温时效对G115钢蠕变-疲劳裂纹扩展行为的影响

赵欣^1,2, 陈正宗¹, 唐正焮¹

1.钢铁研究总院有限公司特殊钢研究院, 北京 100081;
2.宝武特种冶金有限公司技术中心, 上海 200940

收稿日期:2022-03-14 修回日期:2023-06-02 出版日期:2023-07-25 发布日期:2023-09-04
作者简介:赵欣(1981—),男,高级工程师,主要研究方向为材料研发,E-mail: 080433@baosteel.com。
基金资助:
国家重点研发计划(2021YFB3704104)

Effect of elevated-temperature aging on creep-fatigue crack growth behavior of G115 steel

Zhao Xin^1,2, Chen Zhengzong¹, Tang Zhengxin¹

1. Research Institute of Special Steels, Central Iron and Steel Research Institute Co., Ltd., Beijing 100081, China;
2. R&D Centre Baowu Special Metallurgy Co., Ltd., Shanghai 200940, China

Received:2022-03-14 Revised:2023-06-02 Online:2023-07-25 Published:2023-09-04

摘要/Abstract

摘要： 在保载时间600 s,初始应力强度因子范围为23 MPa·m^0.5条件下,研究了G115钢在650 ℃时效1000、2000和3000 h后的蠕变-疲劳裂纹扩展行为。结果表明,随着时效时间的增加,时效后G115钢蠕变-疲劳裂纹扩展速率da/dN显著增加,导致裂纹扩展寿命降低。然而,时效时间的变化对裂纹扩展机制无显著影响,均为伴随大量蠕变损伤的穿晶主导混合断裂模式。沿边界Laves相的快速形核和长大、固溶作用的降低是导致时效后G115钢蠕变-疲劳裂纹扩展寿命降低的主要原因。

关键词: G115钢, 高温时效, 蠕变-疲劳, 裂纹扩展

Abstract: Creep-fatigue crack growth behavior of G115 steel aged at 650 ℃ for 1000, 2000 and 3000 h was investigated under the condition of holding time 600 s and initial stress intensity factor 23 MPa·m^0.5. The results reveal that the creep-fatigue crack growth rate da/dN increases with the aging time, causing the decrease of the crack propagation life. However, the change of aging time has no significant effect on crack propagation mechanism, which is a transgranular dominant mixed fracture mode with a large number of creep damage. The rapid nucleation and growth of Laves phase along the boundaries and the reduction of solid solution effect are the main reasons for the reduction of creep-fatigue crack growth life of G115 steel after aging.

Key words: G115 steel, elevated-temperature aging, creep-fatigue, crack growth

中图分类号:

TG142.1

赵欣, 陈正宗, 唐正焮. 高温时效对G115钢蠕变-疲劳裂纹扩展行为的影响[J]. 金属热处理, 2023, 48(7): 26-31.

Zhao Xin, Chen Zhengzong, Tang Zhengxin. Effect of elevated-temperature aging on creep-fatigue crack growth behavior of G115 steel[J]. Heat Treatment of Metals, 2023, 48(7): 26-31.

参考文献

[1]刘正东, 陈正宗, 包汉生, 等. 新一代马氏体耐热钢G115研发及工程化[M]. 北京: 冶金工业出版社, 2020.
[2]赵欣, 陈正宗, 赵海平. 新型马氏体耐热钢G115大型铸件热处理过程有限元分析[J]. 金属热处理, 2022, 47(2): 229-236.
Zhao Xin, Chen Zhengzong, Zhao Haiping. Finite element analysis of novel martensitic heat-resistant steel G115 heavy castings[J]. Heat Treatment of Metals, 2022, 47(2): 229-236.
[3]刘正东, 陈正宗, 何西扣, 等. 630~700 ℃超超临界燃煤电站耐热管及其制造技术进展[J]. 金属学报, 2020, 56(4): 539-548.
Liu Zhengdong, Chen Zhengzong, He Xikou, et al. Systematical innovation of heat resistant materials used for 630-700 ℃ advanced ultra-supercritical(A-USC) fossil fired boilers[J]. Acta Metallurgica Sinica, 2020, 56(4): 539-548.
[4]雷丙旺, 李永清, 庞海平, 等. 新型马氏体耐热钢G115大口径厚壁无缝钢管制造技术[J]. 金属功能材料, 2020, 27(5): 14-19.
Lei Bingwang, Li Yongqing, Pang Haiping, et al. Manufacturing technology of novel heat resistant steel G115 large-diameter heavy wall seamless pipe[J]. Metallic Functional Materials, 2020, 27(5): 14-19.
[5]徐连勇, 赵雷, 唐正焮. 高温部件蠕变-疲劳裂纹扩展行为表征[J]. 电力科技与环保, 2021, 37(4): 1-11.
Xu Lianyong, Zhao Lei, Tang Zhengxin. Characterization of creep-fatigue crack growth behavior for high temperature components[J]. Electric Power Technology and Environmental Protection, 2021, 37(4): 1-11.
[6]Tang Z, Jing H, Xu L, et al. Creep-fatigue crack growth behavior of G115 steel under different hold time conditions[J]. International Journal of Fatigue, 2018, 116: 572-583.
[7]Tang Z, Jing H, Xu L, et al. Crack growth behavior, fracture mechanism, and microstructural evolution of G115 steel under creep-fatigue loading conditions[J]. International Journal of Mechanical Sciences, 2019, 161-162: 105037.
[8]Tang Z, Jing H, Xu L, et al. Temperature effect on dwell-fatigue crack propagation behavior of novel tempered martensitic ferritic steel G115[J]. Engineering Fracture Mechanics, 2020, 237: 107250.
[9]Abe F. Precipitate design for creep strengthening of 9%Cr tempered martensitic steel for ultra-supercritical power plants[J]. Science and Technology of Advanced Materials, 2008, 9(1): 013002.
[10]He Y S, Chang J C, Lee J Y, et al. Effect of aging on the creep properties and microstructural evolution of P92 steel[J]. Key Engineering Materials, 2017, 727: 52-58.
[11]Wang X, Xu Q, Yu S, et al. Laves-phase evolution during aging in 9Cr-1.8W-0.5Mo-VNb steel for USC power plants[J]. Materials Chemistry and Physics, 2015, 163: 219-228.
[12]Fedorova I, Belyakov A, Kozlov P, et al. Laves-phase precipitates in a low-carbon 9%Cr martensitic steel during aging and creep at 923 K[J]. Materials Science and Engineering A, 2014, 615: 153-163.
[13]Sakthivel T, Laha K, Parameswaran P, et al. Effect of thermal aging on microstructure and mechanical properties of P92 steel[J]. Transactions of the Indian Institute of Metals, 2015, 68(3): 411-421.
[14]Sklenicka V, Kucharova K, Svobodova M, et al. The effect of a prior short-term ageing on mechanical and creep properties of P92 steel[J]. Materials Characterization, 2018, 136: 388-397.
[15]Sasaki L, Hénaff G, Arzaghi M, et al. Effect of long term aging on the fatigue crack propagation in the β titanium alloy Ti 17[J]. Materials Science and Engineering A, 2017, 707: 253-258.
[16]ASTM E2760-16. Standard test method for creep-fatigue crack growth testing[S].
[17]梁宝琦, 孙嘉欣, 程义, 等. G115钢650 ℃时效的组织与性能研究[J]. 锅炉制造, 2021(5): 45-48, 60.
Liang Baoqi, Sun Jiaxin, Cheng Yi, et al. Study on microstructure and mechanical properties of G115 steel aged at 650 ℃[J]. Boiler Manufacturing, 2021(5): 45-48, 60.
[18]Yang H, Bao R, Zhang J, et al. Crack growth behaviour of a nickel-based powder metallurgy superalloy under elevated temperature[J]. International Journal of Fatigue, 2011, 33(4): 632-641.

高温时效对G115钢蠕变-疲劳裂纹扩展行为的影响

Effect of elevated-temperature aging on creep-fatigue crack growth behavior of G115 steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	田力男, 张丰收, 李俊峰, 白丽, 王鲁, 乔立捷, 冯可云. G115钢管埋弧自动焊焊缝冲击性能不足的原因分析及热处理修复措施[J]. 金属热处理, 2023, 48(4): 293-297.
[2]	张开, 王学, 倪满生, 刘俊建, 杜成超. 高温时效对P91钢组织及硬度的影响[J]. 金属热处理, 2022, 47(12): 7-12.
[3]	高艾瑞, 高圆, 席生岐, 石联峰, 梁刚, 高振旭. 不同温度时效后17-4PH不锈钢的高周腐蚀疲劳性能[J]. 金属热处理, 2021, 46(4): 187-191.
[4]	丛相州, 彭杏娜, 彭先宽, 王涛, 陈正宗, 姜海峰, 李传永, 张书迎. G115钢大口径管件的热处理[J]. 金属热处理, 2021, 46(3): 90-95.
[5]	刘心阳, 陈正宗, 周芸, 包汉生. 热处理工艺对G115钢铸件组织与性能的影响[J]. 金属热处理, 2021, 46(10): 65-73.
[6]	潘仁杰, 陈康敏, 郭辉, 范世通. 固溶处理时间对Al-5.7Zn-0.7Mg铝合金型材组织及压溃性能的影响[J]. 金属热处理, 2021, 46(10): 101-107.
[7]	齐向前. 焊后回火温度对G115钢熔敷金属组织及室温力学性能的影响[J]. 金属热处理, 2021, 46(10): 199-203.
[8]	张旭, 何文超, 李东辉, 肖茂果, 李绍宏. 热作模具钢热疲劳机理及性能改善的研究现状[J]. 金属热处理, 2020, 45(9): 10-20.
[9]	樊磊, 张仁奇, 李波, 王凌旭, 何锦航, 邹长飞, 梁宇. 水射流喷丸对渗碳钢表层组织与裂纹扩展性能的影响[J]. 金属热处理, 2020, 45(9): 129-133.
[10]	牛延龙, 刘岩松, 刘清友, 贾书君, 童帅, 汪兵. 针状铁素体管线钢的低温韧性与“有效晶粒尺寸”的新定义[J]. 金属热处理, 2020, 45(7): 101-110.
[11]	罗家元, 贾二锁. 淬火残余应力对铝合金厚板裂纹应力强度因子及扩展趋势的影响[J]. 金属热处理, 2020, 45(5): 210-214.
[12]	王兆民, 王硕, 申雷, 程义. 22Cr-25Ni奥氏体耐热钢高温时效的组织及性能[J]. 金属热处理, 2020, 45(3): 46-49.
[13]	徐鹏飞, 赵作鹏, 程红霞, 肖福仁. X80管线钢焊接热模拟热影响区疲劳裂纹扩展行为的分析及预测[J]. 金属热处理, 2020, 45(12): 184-188.
[14]	李云昆, 周芸, 时捷, 尉文超, 何肖飞, 胡芳忠, 王毛球. 亚温淬火-回火组织对18CrNiMo7-6齿轮钢疲劳性能的影响[J]. 金属热处理, 2020, 45(11): 19-25.
[15]	黄志伟，汪静雪，张兴权，段士伟，陈斌，黄志来，裴善报. 循环载荷幅值对7075-T7451铝合金疲劳裂纹扩展行为的影响[J]. 金属热处理, 2016, 41(9): 38-42.