X80管线钢的过冷奥氏体转变规律和相变模型

doi:10.13251/j.issn.0254-6051.2023.07.011

金属热处理 ›› 2023, Vol. 48 ›› Issue (7): 61-65.DOI: 10.13251/j.issn.0254-6051.2023.07.011

X80管线钢的过冷奥氏体转变规律和相变模型

谭会杰¹, 鲍小光², 吴忠旺¹, 王海燕¹

1.内蒙古科技大学材料与冶金学院, 内蒙古包头 014010;
2.包钢(集团)公司轨梁轧钢厂, 内蒙古包头 014010

收稿日期:2023-01-06 修回日期:2023-05-22 出版日期:2023-07-25 发布日期:2023-09-04
通讯作者: 吴忠旺,副研究员,博士后,E-mail: wuzw79@163.com
作者简介:谭会杰(1989—),女,实验师,硕士,主要研究方向为金属材料组织与性能及理化检测,E-mail: 18347845799@126.com。
基金资助:
内蒙古自治区科技攻关项目(2020GG0150)

Transformation law of super-cooled austenite and phase transformation model of X80 pipeline steel

Tan Huijie¹, Bao Xiaoguang², Wu Zhongwang¹, Wang Haiyan¹

1. School of Materials and Metallurgy, Inner Mongolia University of Science and Technology, Baotou Inner Mongolia 014010, China;
2. Baogang(Group) Company Rail and Beam Factory, Baotou Inner Mongolia 014010, China

Received:2023-01-06 Revised:2023-05-22 Online:2023-07-25 Published:2023-09-04

摘要/Abstract

摘要： 利用L78RITA淬火热膨胀仪研究了X80管线钢过冷奥氏体转变的相变规律,结合金相-硬度法绘制了试验钢的连续冷却转变(CCT)曲线。结果表明,随着冷却速率的增加,X80管线钢过冷奥氏体分别发生了铁素体、贝氏体、马氏体转变;冷速小于3 ℃/s时,组织为铁素体和贝氏体;冷速在3~20 ℃/s时,组织只有贝氏体;冷速大于40 ℃/s时,组织中开始出现马氏体,且随着冷速的进一步增大,马氏体的含量逐渐增多,贝氏体逐渐减少直至消失。试验钢硬度随着冷却速率的增加呈逐步升高的趋势。在CCT曲线基础上,建立了相变点温度-冷却速率关系模型,并通过回归计算得到拟合度较高的相变模型,且模型计算值与试验值之间能够很好的地吻合,证明了该相变模型的可行性。

关键词: X80管线钢, 连续冷却转变, 冷却速率, 相变模型

Abstract: Phase transformation law of super-cooled austenite in X80 pipeline steel was studied by means of L78RITA dilatometer, and continuous cooling transformation curves of the tested steel were plotted combining with metallographic hardness method. The results show that with the increase of cooling rate, ferrite transformation, bainite transformation and martensite transformation occur in the super-cooled austenite of the X80 pipeline steel, respectively. When the cooling rate is less than 3 ℃/s, the microstructure is ferrite and bainite. When the cooling rate is 3-20 ℃/s, only bainite is found in the microstructure. When the cooling rate is higher than 40 ℃/s, martensite begins to appear, and with the further increase of the cooling rate, the content of martensite gradually increases, while the bainite gradually decreases and disappears. The hardness of the tested steel increases gradually with the increase of the cooling rate. Based on the CCT curves, the relationship model of phase transformation temperature-cooling rate is established, phase transformation model with high fit degree is gained by regression calculation, and the calculated value and test value are nearly similar that proves the feasibility of the phase transition model.

Key words: X80 pipeline steel, continuous cooling transformation, cooling rate, phase transformation model

中图分类号:

TG142.1

谭会杰, 鲍小光, 吴忠旺, 王海燕. X80管线钢的过冷奥氏体转变规律和相变模型[J]. 金属热处理, 2023, 48(7): 61-65.

Tan Huijie, Bao Xiaoguang, Wu Zhongwang, Wang Haiyan. Transformation law of super-cooled austenite and phase transformation model of X80 pipeline steel[J]. Heat Treatment of Metals, 2023, 48(7): 61-65.

参考文献

[1]De Ardo A J. Multi-phase microstructures and their properties in high strength low carbon steels[J]. ISIJ International, 1995, 35(6): 946-954.
[2]赵运堂, 尚成嘉, 杨善武, 等. 低碳微合金钢在过冷奥氏体亚稳定区的转变[J]. 北京科技大学学报, 2007, 29(7): 694-698.
Zhao Yuntang, Shang Chengjia, Yang Shanwu, et al. Metastable austenite transformation in low carbon microalloying steel[J]. Journal of University of Science and Technology Beijing, 2007, 29(7): 694-698.
[3]元亚莎, 石如星, 元莎, 等. 55NiCrMoV7钢的过冷奥氏体连续冷却转变曲线[J]. 材料热处理学报, 2022, 43(3): 114-119.
Yuan Yasha, Shi Ruxing, Yuan Sha, et al. Continuous cooling transformation curves of undercooled austenite of 55NiCrMoV7 steel[J]. Transactions of Materials and Heat Treatment, 2022, 43(3): 114-119.
[4]赵楠, 薛峰, 潘进, 等. 不同冷速对700 MPa级汽车大梁钢过冷奥氏体转变的影响[J]. 金属热处理, 2021, 46(2): 178-181.
Zhao Nan, Xue Feng, Pan Jin, et al. Effect of cooling rate on undercooling austenite transformation of 700 MPa automotive beam steel[J]. Heat Treatment of Metals, 2021, 46(2): 178-181.
[5]王壮飞, 唐帅, 刘振宇, 等. Nb对低碳微合金钢连续冷却相变行为的影响[J]. 东北大学学报(自然科学版), 2014, 35(8): 1117-1119.
Wang Zhuangfei, Tang Shuai, Liu Zhenyu, et al. Effect of Nb on continuous cooling transformation behavior of low carbon microalloyed steel[J]. Journal of Northeastern University(Natural Science), 2014, 35(8): 1117-1119.
[6]林乙丑, 张彦敏, 张广威, 等. 1.25Cr0.5MoSiNb 钢过冷奥氏体连续冷却转变[J]. 材料热处理学报, 2021, 42(1): 119-125.
Lin Yichou, Zhang Yanmin, Zhang Guangwei, et al. Continuous cooling transformation of supercooled austenite of 1.25Cr0.5MoSiNb steel[J]. Transactions of Materials and Heat Treatment, 2021, 42(1): 119-125.
[7]谭会杰, 王海燕, 李德超, 等. X80管线钢连续冷却相变及组织研究[J]. 金属热处理, 2015, 40(7): 91-94.
Tan Huijie, Wang Haiyan, Li Dechao, et al. Continuous cooling transformation and microstructure of X80 pipeline steel[J]. Heat Treatment of Metals, 2015, 40(7): 91-94.
[8]庞庆海, 郎庆斌, 马窦琴, 等. 2.25Cr1Mo0.25V钢连续冷却转变过程的相变行为[J]. 金属热处理, 2019, 44(2): 12-16.
Pang Qinghai, Lang Qingbin, Ma Douqin, et al. Continuous cooling transformation behavior of 2.25Cr1Mo0.25V steel[J]. Heat Treatment of Metals, 2019, 44(2): 12-16.
[9]邓鹏, 宋仁伯, 孙挺, 等. 70Mn钢连续冷却转变曲线及其相变模型[J]. 材料热处理学报, 2014, 35(4): 208-212.
Deng Peng, Song Renbo, Sun Ting, et al. Continuous cooling transformation diagram and phase transformation model of 70Mn steel[J]. Transactions of Materials and Heat Treatment, 2014, 35(4): 208-212.
[10]赵宝纯, 张涛, 李桂艳, 等. 低合金高强钢形变奥氏体相变行为及其模型[J]. 钢铁, 2019, 54(7): 98-102.
Zhao Baochun, Zhang Tao, Li Guiyan, et al. Continuous cooling transformation behavior and modeling of hot deformed austenite in a HSLA steel[J]. Iron and Steel, 2019, 54(7): 98-102.
[11]蔡恒君, 高喆, 宋仁伯, 等. 低碳低合金高强钢的连续转变行为及其相变模型[J]. 材料热处理学报, 2015, 36(3): 214-219.
Cai Hengjun, Gao Zhe, Song Renbo, et al. Continuous cooling transformation behavior and phase transformation model in low carbon HSLA steel[J]. Transactions of Materials and Heat Treatment, 2015, 36(3): 214-219.
[12]李曼云, 孙本荣. 钢的控制轧制和控制冷却技术手册[M]. 北京: 冶金工业出版社, 1990.

[1]	赵倩, 乔志霞, 董纪, 张亚然, 何彪, 钱阔. WB36CN1钢连续冷却转变产物分析[J]. 金属热处理, 2023, 48(7): 22-25.
[2]	徐海峰, 李海, 李凤敏, 付胜敏, 明科宇, 郁言. 新型槽帮钢的连续冷却转变曲线及微观组织[J]. 金属热处理, 2023, 48(6): 191-196.
[3]	陈子宏, 薛正良, 刘孟珂, 张翔, 郑顶立, 马国军. 残余元素Sb对X80管线钢力学性能的影响[J]. 金属热处理, 2023, 48(3): 248-253.
[4]	马静, 罗鸿, 王申豪, 童安琪, 李建辉, 王建刚, 冯志浩, 陈义庆. 外加电位下X80双相管线钢在模拟沿海土壤环境中的应力腐蚀行为[J]. 金属热处理, 2023, 48(2): 30-35.
[5]	刘彦强, 杨浩, 张志军, 贾书君, 韩鹏彪. 变形条件和冷却速率对低碳含Nb钢的相变及纳米析出的影响[J]. 金属热处理, 2023, 48(2): 110-116.
[6]	黄朋, 镇凡, 杜平, 曲锦波. 薄规格耐磨钢淬火条纹分析与工艺改进[J]. 金属热处理, 2023, 48(1): 266-269.
[7]	王瑞敏, 刘曼, 周剑华, 张琪, 苏雪, 徐光. R350HT钢轨钢的连续冷却转变曲线[J]. 金属热处理, 2022, 47(9): 153-157.
[8]	骆艳萍, 汪家晗, 李沐泽, 张云祥, 周建勋, 赵志恒. HRB400E抗震螺纹钢静态CCT曲线测定及组织分析[J]. 金属热处理, 2022, 47(9): 188-193.
[9]	张铮, 陈进磊, 张敏, 乔珺威. 热变形对塑料模具钢SDFT600贝氏体相变的影响[J]. 金属热处理, 2022, 47(8): 1-6.
[10]	沈慧, 刘云鹏, 斯庭智. 4330M钢连续冷却过程中的组织转变特征[J]. 金属热处理, 2022, 47(7): 190-196.
[11]	吴轲源, 刘云鹏, 李孔斋, 徐良乐. 17-4PH不锈钢连续冷却转变及相变动力学[J]. 金属热处理, 2022, 47(6): 161-167.
[12]	李阳, 张建伟, 朱鹏凯, 杨扬. 碳含量及冷却速率对钢件淬火残余应力的影响[J]. 金属热处理, 2022, 47(6): 192-195.
[13]	庞庆海, 郎庆斌, 何春静, 王九花, 元亚莎. 5Cr2NiMoVSi模具钢的相变规律与力学性能[J]. 金属热处理, 2022, 47(3): 186-190.
[14]	夏士超, 耿铁强, 李文, 李宏, 朱正旺. 冷却速率对Ti_40.9Zr_30.4Nb_4.2Cu₇Ni_1.7Be_15.8内生型非晶合金复合材料组织及性能的影响[J]. 金属热处理, 2022, 47(10): 65-70.
[15]	田俊, 苏丽娟, 吴静, 黄圣珑, 王德永. Mg对X80管线钢夹杂物和奥氏体晶粒尺寸的影响[J]. 金属热处理, 2022, 47(10): 71-77.

X80管线钢的过冷奥氏体转变规律和相变模型

Transformation law of super-cooled austenite and phase transformation model of X80 pipeline steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价