高强度帘线钢LX82ACr的动态连续冷却转变行为

doi:10.13251/j.issn.0254-6051.2023.09.036

金属热处理 ›› 2023, Vol. 48 ›› Issue (9): 214-219.DOI: 10.13251/j.issn.0254-6051.2023.09.036

高强度帘线钢LX82ACr的动态连续冷却转变行为

李战卫, 沈奎, 麻晗, 张宇

江苏省(沙钢)钢铁研究院, 江苏张家港 215625

收稿日期:2023-03-27 修回日期:2023-07-23 出版日期:2023-09-25 发布日期:2023-10-25
通讯作者: 沈奎,高级工程师,硕士,E-mail:shenkui2004@163.com
作者简介:李战卫(1984—),男,工程师,主要研究方向为钢铁材料棒线材产品开发,E-mail:lzwfm@126.com。

Phase transformation behavior of high strength cord steel LX82ACr during dynamic continuous cooling

Li Zhanwei, Shen Kui, Ma Han, Zhang Yu

Institute of Research of Iron & Steel, Sha-steel, Zhangjiagang Jiangsu 215625, China

Received:2023-03-27 Revised:2023-07-23 Online:2023-09-25 Published:2023-10-25

摘要/Abstract

摘要： 通过热模拟试验研究了LX82ACr帘线钢的动态连续冷却转变规律,采用OM对不同冷速冷却后的试样进行显微组织分析。研究了相变温度和过冷度随冷速的变化规律。对不同冷速冷却后的试样进行珠光体片层间距测量和硬度测量,并进行抗拉强度换算,研究了珠光体片层间距和抗拉强度随冷速的变化规律。结果表明,当冷速在3 ℃/s及以下时,转变后的组织为珠光体和索氏体;当冷速达到5 ℃/s时,组织中开始出现马氏体;随着冷速提高,马氏体含量逐渐增多,当冷速达到30 ℃/s及以上时,组织以马氏体为主。随着冷速提高,相变温度逐渐降低,过冷度逐渐增大,进行回归分析,拟合优度达到0.97以上。随着冷速提高,珠光体片层间距逐渐变细,抗拉强度逐渐提高,当冷速从0.1 ℃/s提高至9 ℃/s时,珠光体片层间距由0.1929 μm减小至0.0739 μm,抗拉强度由993.2 MPa提高至1388.4 MPa。分别对珠光体片层间距和抗拉强度进行回归分析,拟合优度均达到0.97以上。

关键词: 帘线钢, 动态连续冷却, 相变温度, 珠光体片层间距, 抗拉强度

Abstract: Characteristics of LX82ACr cord steel during dynamic continuous cooling were studied by thermal simulation, and the microstructures at different cooling rates were analyzed by using optical microscope. The pearlite lamellar spacing and hardness were measured at different cooling rates, and the tensile strength was converted from the hardness. The variation characteristics of phase transformation temperature, undercooling degree, pearlite lamellar spacing, and tensile strength with cooling rate were studied, respectively. The results show that when the cooling rate is 3 ℃/s and below, the microstructure is pearlite and sorbite. When the cooling rate reaches 5 ℃/s, the martensite begins to appear and its quantity increases with the increase of cooling rate. When the cooling rate reaches 30 ℃/s and above, the microstructure is mainly martensite. The phase transformation temperature decreases and the undercooling degree increases with the increase of cooling rate, and the regression analyses show that the goodness of each fitting reaches above 0.97. The pearlite lamellar spacing decreases and the tensile strength increases with the increase of cooling rate, and the regression analyses show that the goodness of each fit is also above 0.97. When the cooling rate increases from 0.1 ℃/s to 9 ℃/s, the pearlite lamellar spacing decreases from 0.1929 μm to 0.0739 μm, and the tensile strength increases from 993.2 MPa to 1388.4 MPa.

Key words: cord steel, dynamic continuous cooling, phase transformation temperature, pearlite lamellar spacing, tensile strength

中图分类号:

TG156.6

李战卫, 沈奎, 麻晗, 张宇. 高强度帘线钢LX82ACr的动态连续冷却转变行为[J]. 金属热处理, 2023, 48(9): 214-219.

Li Zhanwei, Shen Kui, Ma Han, Zhang Yu. Phase transformation behavior of high strength cord steel LX82ACr during dynamic continuous cooling[J]. Heat Treatment of Metals, 2023, 48(9): 214-219.

参考文献

[1]王洪利, 刘宏玉, 王瑞敏, 等. 帘线钢微合金化组织与性能研究[J]. 金属制品, 2011, 37(4): 62-65, 69.
Wang Hongli, Liu Hongyu, Wang Ruimin, et al. Study on microstructure and property of tire cord steel microalloying[J]. Metal Products, 2011, 37(4): 62-65, 69.
[2]麻晗, 王世芳. 节能型钢筋、线材的研发与生产实践[J]. 金属热处理, 2013, 38(7): 1-9.
Ma Han, Wang Shifang. Development and practice of energy saving steel reinforcing bar and wire[J]. Heat Treatment of Metals, 2013, 38(7): 1-9.
[3]周志嵩, 孙忍, 姚海东, 等. 微合金化高碳盘条生产钢帘线研究[C]//第十二届中国钢铁年会论文集—5. 金属材料深加工, 2019: 108-113.
Zhou Zhisong, Sun Ren, Yao Haidong, et al. Study on steel cords produced by microalloying high-carbon wire rods[C]// Proceedings of the 12th CSM Steel Congress-5. Deep Processing of Metal Materials, 2019: 108-113.
[4]郭健. 微合金元素Cr高碳钢组织性能研究[J]. 河北冶金, 2000(1): 8-9, 52.
Guo Jian. Organism and performance research for high-carbon steel with microalloy element Cr[J]. Hebei Metallurgy, 2000(1): 8-9, 52.
[5]崔忠圻, 覃耀春. 金属学与热处理[M]. 北京: 机械工业出版社, 2007: 243.
[6]卫广智, 潘广明, 齐福利. SWRH82B珠光体片层间距计算模型研究[J]. 现代机械, 2012(1): 72-73, 88.
Wei Guangzhi, Pan Guangming, Qi Fuli. Research on the calculation models of interlamellar spacing of pearlite in SWRH82B steel[J]. Modern Machinery, 2012(1): 72-73, 88.
[7]Kumar A, McCulloch C, Hawbolt E B, et al. Modelling thermal and microstructural evolution on runout table of hot strip mill[J]. Material Science and Technology, 1991, 7(4): 360-368.
[8]李战卫, 沈奎, 于学森, 等. 超高强度帘线钢LX92A连续和等温冷却下的相变行为[J]. 金属热处理, 2021, 46(5): 32-38.
Li Zhanwei, Shen Kui, Yu Xuesen, et al. Phase transformation behaviors of ultra high strength cord steel LX92A in continuous cooling and isothermal cooling[J]. Heat Treatment of Metals, 2021, 46(5): 32-38.
[9]Elwazri A M, Wanjara P, Yue S. Empirical modelling of the isothermal transformation of pearlite in hypereutectoid steel[J]. Materials Science and Technology, 2006, 22(5): 542-546.
[10]Phadke S, Pauskar P, Shivpuri R. Computational modeling of phase transformations and mechanical properties during the cooling of hot rolled rod[J]. Journal of Materials Processing Technology, 2004, 150(1): 107-115.
[11]Kazeminezhad M, Karimi Taheri A. The effect of controlled cooling after hot rolling on the mechanical properties of a commercial high carbon steel wire rod[J]. Materials and Design, 2003, 24(6): 415-421.
[12]Han K, Edmonds D V, Smith G D W. Optimization of mechanical properties of high-carbon pearlitic steels with Si and V additions[J]. Metallurgical and Materials Transactions A. Physical Metallurgy and Materials Science, 2001, 32(6): 1313-1324.
[13]Elwazri A M, Wanjara P, Yue S. The effect of microstructural characteristics of pearlite on the mechanical properties of hypereutectoid steel[J]. Materials Science and Engineering A, 2005, 404(1): 91-98.

[1]	张连有, 赵卓, 车安, 李灵敏, 周艳文, 陈雪娇, 谢世绵, 吕哲. T90高碳帘线钢加热过程奥氏体晶粒长大规律与数学模型[J]. 金属热处理, 2023, 48(8): 118-123.
[2]	韩贵生, 张学敏, 李海涛, 樊帅奇, 戴姣燕, 徐金富. 42CrMoVNb钢的热处理工艺优化及力学性能[J]. 金属热处理, 2023, 48(4): 161-165.
[3]	马英建, 彭其春, 袁清, 梁亮, 齐江华, 肖爱达, 薛正良. 热轧低密度钢Fe-1.80Mn-1.05Al-0.09C的高温热塑性[J]. 金属热处理, 2023, 48(2): 43-49.
[4]	褚峰, 沈奎, 胡显军, 张继明. 高碳帘线钢的冷却相变行为[J]. 金属热处理, 2023, 48(2): 79-84.
[5]	陈焕德, 麻晗, 孙国才, 张宇. 超高强度悬架弹簧用钢55SiCrNb的工业试制[J]. 金属热处理, 2022, 47(9): 208-213.
[6]	刘昱君, 程晓农, 罗锐, 高佩. 热处理工艺对Inconel 617合金管组织性能的影响[J]. 金属热处理, 2022, 47(2): 173-177.
[7]	曾延琦, 余辉辉, 陆德平, 张友亮, 胡强, 郭军力, 胡斐斐, 邹晋. 成品退火工艺对Cu-20wt%Fe原位复合带材组织和性能的影响[J]. 金属热处理, 2022, 47(10): 169-172.
[8]	李昂, 高坤元, 文胜平, 黄晖, 聂祚仁. 冷却条件对5E83铝合金搅拌摩擦焊接头组织与性能的影响[J]. 金属热处理, 2022, 47(1): 130-134.
[9]	侯瑾睿, 张爽, 张毅, 张凌峰. 模拟烧伤温度对TC4-DT钛合金组织与性能的影响[J]. 金属热处理, 2021, 46(9): 199-204.
[10]	李战卫, 沈奎, 于学森, 张宇. 超高强度帘线钢LX92A连续和等温冷却下的相变行为[J]. 金属热处理, 2021, 46(5): 32-37.
[11]	禹润缜, 赵峰, 余圣甫, 李勇杰, 唐论. 电弧熔丝增材制造ER2319铝堆积金属的组织性能及T6热处理工艺优化[J]. 金属热处理, 2021, 46(4): 49-59.
[12]	王东梅, 赵磊城, 陈林, 包喜荣, 郭瑞华. 淬火冷速对过共析轨钢中珠光体组织的影响[J]. 金属热处理, 2021, 46(3): 12-16.
[13]	段伟, 简思聪, 伍超群, 肖永通, 卢凤池, 李雨, 胡子建, 明亮. 基于CCD的多级时效工艺对6061铝合金性能的影响[J]. 金属热处理, 2021, 46(10): 96-100.
[14]	孙跃军, 仲丽, 崔泽文, 赵康培, 丁代存, 王雷. 时效处理对Al-Mg-4.5Si-4.5Zn合金性能的影响[J]. 金属热处理, 2021, 46(10): 117-121.
[15]	汪思敏, 胡志华, 王正云, 栾道成, 王楠, 陈杰. 回火温度对汽车用22MnB5钢组织和性能的影响[J]. 金属热处理, 2020, 45(7): 32-36.

高强度帘线钢LX82ACr的动态连续冷却转变行为

Phase transformation behavior of high strength cord steel LX82ACr during dynamic continuous cooling

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价