NM500耐磨钢的QLT热处理工艺

doi:10.13251/j.issn.0254-6051.2023.10.023

金属热处理 ›› 2023, Vol. 48 ›› Issue (10): 157-162.DOI: 10.13251/j.issn.0254-6051.2023.10.023

NM500耐磨钢的QLT热处理工艺

张蒙, 吴光亮

中南大学资源加工与生物工程学院, 湖南长沙 410083

收稿日期:2023-05-17 修回日期:2023-08-15 出版日期:2023-10-25 发布日期:2023-12-07
通讯作者: 吴光亮,教授,博士,E-mail:glwu_899@sina.com
作者简介:张蒙(1997—),女,硕士,主要研究方向为低合金高强度耐磨钢的组织性能,E-mail:2359194863@qq.com。

QLT heat treatment process of NM500 wear-resistant steel

Zhang Meng, Wu Guangliang

School of Minerals Processing and Bioengineering, Central South University, Changsha Hunan 410083, China

Received:2023-05-17 Revised:2023-08-15 Online:2023-10-25 Published:2023-12-07

摘要/Abstract

摘要： 对NM500耐磨钢进行940 ℃淬火+两相区淬火+回火(QLT)热处理,研究了两相区淬火温度(820~880 ℃)和回火温度(200~600 ℃)对试验钢显微组织和力学性能的影响。结果表明,在两相区淬火温度从820 ℃升至880 ℃的过程中,试验钢为马氏体和铁素体双相组织,且铁素体含量逐渐降低,马氏体含量增多,试验钢的强度和硬度提高,-40 ℃冲击吸收能量从67 J降低至33 J。在870 ℃两相区淬火,200~600 ℃范围内回火时,随回火温度的升高,板条马氏体和残留奥氏体逐渐分解,碳化物形态和分布发生变化;试验钢抗拉强度和硬度逐渐降低,低温冲击性能先降低后升高,试验钢达到良好强韧性匹配的回火温度区间为200~250 ℃。

关键词: 耐磨钢, 两相区淬火, 显微组织, 力学性能

Abstract: NM500 wear-resistant steel was subjected to quenching at 940 ℃, intercritical quenching, and tempering (QLT) treatment, and the effects of the intercritical quenching temperature (820-880 ℃) and tempering temperature (200-600 ℃) on the microstructure and mechanical properties of the tested steel were investigated. The results show that the tested steel is martensitic and ferrite dual-phase after intercritical quenching from 820 ℃ to 880 ℃, and the ferrite content gradually decreases and martensite increases, and the strength and hardness of the tested steel increase, and the impact absorbed energy at -40 ℃ decreases from 67 J to 33 J. When intercritical quenched at 870 ℃ and tempered at the range of 200-600 ℃, with the increase of tempering temperature, the lath martensite and retained austenite gradually decompose, and the morphology and distribution of carbides change. The tensile strength and hardness gradually decrease, and the low temperature impact absorbed energy first decreases and then increases. The tempering temperature range for the tested steel to achieve a good match of strength and toughness is 200-250 ℃.

Key words: wear-resistant steel, intercritical quenching, microstructure, mechanical properties

中图分类号:

TG156

张蒙, 吴光亮. NM500耐磨钢的QLT热处理工艺[J]. 金属热处理, 2023, 48(10): 157-162.

Zhang Meng, Wu Guangliang. QLT heat treatment process of NM500 wear-resistant steel[J]. Heat Treatment of Metals, 2023, 48(10): 157-162.

参考文献

[1]徐锋, 徐进桥. 国内外低合金耐磨钢生产现状及市场分析[J]. 中国钢铁业, 2014, (9): 26-29.
[2]刘军刚, 袁林, 王玮, 等. 耐磨钢生产研究现状与分析[J]. 山东冶金, 2011, 33(2): 7-9.
Liu Jungang, Yuan Lin, Wang Wei, et al. Production situation and analysis of abrasion resisting steel[J]. Shandong Metallurgy, 2011, 33(2): 7-9.
[3]Bartha B B, Zawadzki J, Chandrasekar S, et al. Wear of hard-turned AISI 52100 steel[J]. Metallurgical and Materials Transactions A, 2005, 36(6): 1417-1425.
[4]云妙贤. 低合金高强度耐磨钢组织性能的研究[D]. 沈阳: 东北大学, 2019.
Yun Miaoxian. Study on microstructure and properties of low alloy high strength wear-resistant steel[D]. Shenyang: Northeastern University, 2019.
[5]郑福胜. 热处理工艺对34CrNiMo6组织性能的影响[D]. 沈阳: 东北大学, 2018.
Zheng Fusheng. Effect of heat treatment process on microstructure and properties of 34CrNiMo6[D]. Shenyang: Northeastern University, 2018.
[6]刘志强, 王保华, 黄鑫, 等. 亚温淬火温度对30CrMnSi钢力学性能的影响[J]. 金属热处理, 2015, 40(6): 120-123.
Liu Zhiqiang, Wang Baohua, Huang Xin, et al. Effect of subcritical quenching temperature on properties of 30CrMnSi steel[J]. Heat Treatment of Metals, 2015, 40(6): 120-123.
[7]覃展鹏, 王红鸿, 童志, 等. 亚温淬火工艺对低碳低合金高强钢组织及性能的影响[J]. 材料热处理学报, 2017, 38(9): 142-147.
Qin Zhanpeng, Wang Honghong, Tong Zhi, et al. Influence of lamellarizing process on microstructure and properties of low carbon low alloy high-strength steel[J]. Transactions of Materials and Heat Treatment, 2017, 38(9): 142-147.
[8]贺景春, 姜涛, 李智丽, 等. 两相区淬火对14MnCrMoNiNb钢组织和性能的影响[J]. 包钢科技, 2019, 45(4): 1-3.
He Jingchun, Jiang Tao, Li Zhili, et al. Effects of quenching in two-phase region on microstructure and properties of 14MnCrMoNiNb steel[J]. Science and Technology of Baotou Steel, 2019, 45(4): 1-3.
[9]赵田臣, 樊云昌. 耐候钢热处理双相化组织与性能[J]. 金属热处理, 2001, 26(2): 15-18, 22.
Zhao Tianchen, Fan Yunchang. Microstructures and properties of weathering steels after dual-phase heat treatment[J]. Heat Treatment of Metals, 2001, 26(2): 15-18, 22.
[10]Movahed P, Kolahgar S, Marashi S P H, et al. The effect of intercritical heat treatment temperature on the tensile properties and work hardening behavior of ferrite-martensite dual phase steel sheets[J]. Materials Science and Engineering A, 2009, 518(1): 1-6.
[11]张洁岑. 热轧双相钢组织性能调控及其微观变形机制研究[D]. 沈阳: 东北大学, 2017.
Zhang Jiecen. Study on the control of microstructure-properties of hot-rolled dual phase steel and the micro-deformation mechanism[D]. Shenyang: Northeastern University, 2017.

[1]	孙博, 聂佳民, 李晓丹, 何长树. 强制冷却和低温时效对2198-T3/7A04-T6异种铝合金FSW接头组织及性能的影响[J]. 金属热处理, 2023, 48(9): 8-13.
[2]	崔毅, 崔继红, 王艳, 张雲飞, 俞峰, 赵英利, 曹文全. 淬火工艺对GCr4Mo4V钢组织及耐磨性的影响[J]. 金属热处理, 2023, 48(9): 23-29.
[3]	王毅, 韩杰, 刘超, 邓玲蕊, 李辉, 许荣昌. DQ-T工艺对1000 MPa级高强钢组织和性能的影响[J]. 金属热处理, 2023, 48(9): 30-34.
[4]	韩伟松, 杜峰, 李建锋, 朱宝辉, 沈立华, 刘意, 王鹏. 变形量对Ti80G合金力学性能的影响[J]. 金属热处理, 2023, 48(9): 95-98.
[5]	宋操, 王晓东, 包喜荣, 陈林, 汤雪娇. Ce对30MnNbRE钢淬火回火微观组织和力学性能的影响[J]. 金属热处理, 2023, 48(9): 143-149.
[6]	李文刚, 炊鹏飞, 程尊鹏, 李春梅, 景然, 李江华, 廖仲尼. 硼含量对Ti-Zr-Nb-B合金显微组织及性能的影响[J]. 金属热处理, 2023, 48(9): 157-164.
[7]	戴钊, 郭智, 龙晓燕, 冯晓勇, 刘伟, 张福成, 李艳国. Si含量对高碳贝氏体钢微观组织与性能的影响[J]. 金属热处理, 2023, 48(9): 165-173.
[8]	谢尚恒, 孙有平, 朱嘉欣, 方德俊. 微量Zr对深冷轧制Al-Cu-Mg合金微观组织及性能的影响[J]. 金属热处理, 2023, 48(9): 174-179.
[9]	王英虎. 硫含量对Y12Cr18Ni9易切削钢中硫化物形态及性能的影响[J]. 金属热处理, 2023, 48(9): 183-190.
[10]	李鑫, 武志广, 赵吉庆, 杨钢. 20Cr1Mo1VTiB螺栓钢高温长期时效后的组织演变及力学性能[J]. 金属热处理, 2023, 48(9): 197-202.
[11]	张志春, 温佳, 陈国瑞, 吴广辉, 翁泽钜, 顾开选. 低合金耐磨钢的热处理工艺及力学性能[J]. 金属热处理, 2023, 48(9): 220-224.
[12]	王娇娇, 刘宏春, 刘泳, 陈红卫, 田志强, 张洪起. 一种宽回火时间窗口的10.9级螺栓钢组织和性能[J]. 金属热处理, 2023, 48(9): 233-237.
[13]	刘永珍, 董丽丽, 刘宝志, 张浩, 麻永林. 3.1%Si取向硅钢显微组织和宏观织构演变[J]. 金属热处理, 2023, 48(9): 238-241.
[14]	李子岩, 许鸿翔, 陈业生, 刘志强, 郭敬强, 陈岩, 赵少甫. 42CrMo钢低速轴止推环调质开裂失效分析[J]. 金属热处理, 2023, 48(9): 283-287.
[15]	梁恩溥, 徐乐, 杨勇, 王毛球. Ni含量对NiAl-Cu强化40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2023, 48(8): 1-7.

NM500耐磨钢的QLT热处理工艺

QLT heat treatment process of NM500 wear-resistant steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价