预时效处理对AlZnMgCu铝合金自然时效和烘烤硬化行为的影响

doi:10.13251/j.issn.0254-6051.2023.10.028

金属热处理 ›› 2023, Vol. 48 ›› Issue (10): 188-191.DOI: 10.13251/j.issn.0254-6051.2023.10.028

预时效处理对AlZnMgCu铝合金自然时效和烘烤硬化行为的影响

徐向美¹, 王琪晨²

1.烟台理工学院信息工程学院, 山东烟台 264005;
2.中集海洋工程研究院有限公司, 山东烟台 264670

收稿日期:2023-06-29 修回日期:2023-09-06 出版日期:2023-10-25 发布日期:2023-12-07
作者简介:徐向美(1983—),女,讲师,硕士,主要研究方向为金属材料设计与研究,E-mail: xuxiangmei3112@163.com

Influence of pre-aging on natural aging and bake hardening behavior of AlZnMgCu aluminum alloy

Xu Xiangmei¹, Wang Qichen²

1. College of Information Engineering, Yantai Institute of Technology, Yantai Shandong 264005, China;
2. CIMC Offshore Engineering Institute Company Ltd., Yantai Shandong 264670, China

Received:2023-06-29 Revised:2023-09-06 Online:2023-10-25 Published:2023-12-07

摘要/Abstract

摘要： 研究了一种AlZnMgCu铝合金的自然时效行为,利用预时效处理降低自然时效过程的硬化效果,提升人工时效过程的硬化效应。利用金相显微镜和透射电镜表征了微观组织结构,测试了显微硬度和拉伸性能。结果表明,预时效处理提高了AlZnMgCu铝合金的初始硬度,但经历12天的自然时效后,最终硬度反而小于固溶后直接自然时效的硬度,降低了24%(120 ℃预时效);预时效处理后的试样,经自然时效和180 ℃×20 min的人工时效处理后,屈服强度和抗拉强度分别增大了165 MPa和48 MPa,提高了55.9%和11.2%。固溶+自然时效处理后,基体内GP区尺寸大小不一,分布不均,而经预时效处理后,GP区尺寸和分布均匀,与α-Al基体呈共格关系;预时效+自然时效+人工时效后,η′相粒子尺寸均匀且弥散分布,与α-Al基体呈半共格关系,起到了明显的时效硬化作用。

关键词: AlZnMgCu铝合金, 预时效, 自然时效, 烘烤硬化

Abstract: Natural aging behavior of the AlZnMgCu aluminum alloy was investigated, and the hardening effect of natural aging was reduced by pre-aging treatment, which improved the final hardening effect of artificial aging process. The microstructure was characterized by using OM and TEM, the microhardness and tensile properties were tested. The results indicate that pre-aging treatments improve the initial hardness of the AlZnMgCu alloy, but after natural aging for 12 d, the final hardness is actually lower than that of direct natural aging after solid solution, which is reduced by 24% (pre-aging at 120 ℃). After pre-aging treatment, the yield strength and tensile strength of the specimen increase by 165 MPa and 48 MPa and by 55.9% and 11.2%, respectively, after natural aging and 180 ℃×20 min artificial aging treatment. After solid solution plus natural aging treatment, the distribution of GP zone in the matrix is uneven, while after pre-aging treatment, the size and distribution of GP zone are relatively uniform and exhibits a coherent relationship with α-Al matrix. After pre-aging, natural aging, and artificial aging, η′ phase particles are uniform and dispersed, and exhibit a semi-coherent relationship with α-Al matrix, which plays a significant role in aging hardening.

Key words: AlZnMgCu aluminum alloy, pre-aging, natural aging, bake hardening

中图分类号:

TG156.2

徐向美, 王琪晨. 预时效处理对AlZnMgCu铝合金自然时效和烘烤硬化行为的影响[J]. 金属热处理, 2023, 48(10): 188-191.

Xu Xiangmei, Wang Qichen. Influence of pre-aging on natural aging and bake hardening behavior of AlZnMgCu aluminum alloy[J]. Heat Treatment of Metals, 2023, 48(10): 188-191.

参考文献

[1]霍望图, 郭明星, 侯陇刚, 等. 铝合金先进形变热处理研究进展[J]. 材料科学与工程学报, 2014(2): 284-292.
Huo Wangtu, Guo Mingxing, Hou Longgang, et al. Progress on research of advanced thermo-mechanical treatment of aluminum alloy[J]. Journal of Materials Science and Engineering, 2014(2): 284-292.
[2]杨守杰, 戴圣龙. 航空铝合金的发展回顾与展望[J]. 材料导报, 2005(2): 76-80.
Yang Shoujie, Dai Shenglong. A glimpse at development and application of aluminum alloys in aviation industry[J]. Material Review, 2005(2): 76-80.
[3]Rometsch P A, Zhang Y, Knight S. Heat treatment of 7xxx series aluminium alloys-Some recent developments[J]. Transactions of Nonferrous Metals Society of China, 2014, 24(7): 2003-2017.
[4]Abouarkoub A, Thompson G E, Zhou X, et al. The influence of prolonged natural aging on the subsequent artificial aging response of the AA6111 automotive alloy[J]. Metallurgical and Materials Transactions A, 2015, 46(9): 4380-4393.
[5]Liu M, Cížek J, Chang C S T, et al. Early stages of solute clustering in an Al-Mg-Si alloy[J]. Acta Materialia, 2015, 91: 355-364.
[6]Banhart J, Lay M D H, Chang C S T, et al. Kinetics of natural aging in Al-Mg-Si alloys studied by positron annihilation lifetime spectroscopy[J]. Physical Review B, 2011, 83(1): 101-104.
[7]Aruga Y, Kozuka M, Takaki Y, et al. Effects of natural aging after pre-aging on clustering and bake-hardening behavior in an Al-Mg-Si alloy[J]. Scripta Materialia, 2016, 116: 82-86.
[8]Pogatscher S, Antrekowitsch H, Werinos M, et al. Diffusion on demand to control precipitation aging: Application to Al-Mg-Si alloys[J]. Physical Review Letter, 2014, 112(22): 225-228.
[9]Ferragut R, Somoza A, Tolley A. Microstructural evolution of 7012 alloy during the early stages of artificial ageing[J]. Acta Materialia, 1999, 47(17): 4355-4364.
[10]Berg L K, Gjønnes J, Hansen V, et al. GP-zones in Al-Zn-Mg alloys and their role in artificial aging[J]. Acta Materialia, 2001, 49(17): 3443-3451.
[11]张江斌, 李承波, 何克准, 等. 超厚7085铝合金板时效工艺优化[J]. 金属热处理, 2018, 43(1): 179-183.
Zhang Jiangbin, Li Chengbo, He Kezhun, et al. Optimization of aging process for ultra-thickness 7085 aluminum alloy plate[J]. Heat Treatment of Metals, 2018, 43(1): 179-183.
[12]Dai P, Luo X, Yang Y Q, et al. Nano-scale precipitate evolution and mechanical properties of 7085 aluminum alloy during thermal exposure[J]. Materials Science and Engineering A, 2018, 729: 411-422.
[13]Chen S Y, Chen K H, Peng G S, et al. Effect of heat treatment on hot deformation behavior and microstructure evolution of 7085 aluminum alloy[J]. Journal of Alloys and Compounds, 2012, 537: 338-345.

[1]	周泽宇, 韩明明, 肖翔, 付金来. 退火工艺对7X50铝合金丝材组织与自然时效性能的影响[J]. 金属热处理, 2023, 48(8): 161-165.
[2]	迟蕊, 徐志远, 李涛, 李延成, 王芝东, 张华. 不同热处理工艺下6111铝合金的组织及抗晶间腐蚀[J]. 金属热处理, 2023, 48(6): 95-100.
[3]	杨春苗, 王珊, 王淑慧, 李延珍, 刘文文. RRA过程中预时效时间对7A85铝合金组织性能的影响[J]. 金属热处理, 2022, 47(3): 44-47.
[4]	闵旭东, 黄元春, 肖政兵, 刘宇, 任贤魏, 邹倜. 预处理对汽车用Al-Mg-Si合金组织和晶间腐蚀行为的影响[J]. 金属热处理, 2022, 47(2): 78-85.
[5]	王珊, 王淑慧, 刘文文, 滕敦波, 张日强, 王旭强, 向康宁. 时效处理对7A20铝合金时效硬化响应和晶间腐蚀的影响[J]. 金属热处理, 2021, 46(7): 173-177.
[6]	杜树芳. 时效硬化型渗氮模具钢20Cr3MnMoV的热处理工艺特点[J]. 金属热处理, 2021, 46(3): 71-75.
[7]	王文英, 王慧, 曲世永. 相变诱导塑性钢TRIP590的烘烤硬化特性[J]. 金属热处理, 2020, 45(8): 43-46.
[8]	魏茂源, 王洪真, 张红, 滕敦波. 预时效处理对 Al-Zn-Mg-Cu 合金硬化响应及微观组织的影响[J]. 金属热处理, 2020, 45(7): 90-93.
[9]	李鹏, 赵鲁燕. 预时效对车身用6016铝合金烘烤硬化性能的影响[J]. 金属热处理, 2020, 45(6): 60-62.
[10]	叶志飞, 孙大翔, 周鹏, 邝宏聪, 肖永通. 强变形工艺对2519A铝合金组织与性能的影响[J]. 金属热处理, 2020, 45(5): 187-191.
[11]	姜少婧, 王祖平. 自然时效效应及预时效处理对7A20铝合金组织性能的影响[J]. 金属热处理, 2020, 45(10): 60-63.
[12]	肖来荣, 韦道明, 赵小军, 蔡圳阳, 朴晟铭. 自然时效对GT35合金组织与性能的影响[J]. 金属热处理, 2020, 45(1): 65-68.
[13]	邝春福，郑之旺，王礞. 均热温度对590 MPa级热镀锌双相钢组织性能的影响[J]. 金属热处理, 2016, 41(5): 133-136.
[14]	李辉1,2，张华2，祝贞凤1，赵奇1，江海涛3. 预时效时间对汽车用6016铝合金组织与性能的影响[J]. 金属热处理, 2016, 41(12): 149-152.
[15]	杨晰, 李维娟, 金晓龙, 刘洋, 孙成钱. 固溶碳含量对ULC-BH钢烘烤硬化性能的影响[J]. 金属热处理, 2014, 39(8): 81-84.

预时效处理对AlZnMgCu铝合金自然时效和烘烤硬化行为的影响

Influence of pre-aging on natural aging and bake hardening behavior of AlZnMgCu aluminum alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价