异形C19210铜合金带材的热处理工艺

doi:10.13251/j.issn.0254-6051.2023.10.029

金属热处理 ›› 2023, Vol. 48 ›› Issue (10): 192-197.DOI: 10.13251/j.issn.0254-6051.2023.10.029

异形C19210铜合金带材的热处理工艺

张振峰^1,2, 李翰冬², 陈伟², 秦柳馨², 林高用², 姜雁斌²

1.江苏江顺精密机电设备有限公司, 江苏江阴 214423;
2.中南大学材料科学与工程学院, 湖南长沙 410083

收稿日期:2023-04-11 修回日期:2023-08-03 出版日期:2023-10-25 发布日期:2023-12-07
通讯作者: 林高用,教授,博士,E-mail:gylin6609@csu.edu.cn
作者简介:张振峰(1985—),男,工程师,硕士,主要研究方向为铜铝合金加工技术与装备,E-mail:13812571961@163.com。

Heat treatment process for C19210 copper alloy special-shaped strip

Zhang Zhenfeng^1,2, Li Handong², Chen Wei², Qin Liuxin², Lin Gaoyong², Jiang Yanbin²

1. Jiangsu Jiangshun Precision Mechanical and Electrical Equipment Co., Ltd., Jiangyin Jiangsu 214423, China;
2. School of Materials Science and Engineering, Central South University, Changsha Hunan 410083, China

Received:2023-04-11 Revised:2023-08-03 Online:2023-10-25 Published:2023-12-07

摘要/Abstract

摘要： 结合企业生产实际,针对异形C19210铜合金带材连续挤压-三连轧-钟罩式等温退火-冷轧-连续退火-精轧的工艺方案中的两次退火工艺展开试验研究,以确定其可行的热处理方案。结果表明,C19210铜合金第一次钟罩式退火的较佳工艺为500 ℃×20 h,经冷轧后的导电率约89%IACS,硬度约120 HV0.5。第二次连续退火后合金带材厚料和薄料部分出现明显得性能不均匀现象;改用450 ℃×2 h等温退火处理时,精轧后合金异形带导电率达90.1%IACS,硬度达120 HV0.5左右,且厚料和薄料部分性能均匀。最终获得异形C19210合金带可行的制备工艺为连续挤压-三连轧-500 ℃×20 h罩式等温退火-冷轧-450 ℃×2 h等温退火-精轧。

关键词: C19210铜合金, 异形带材, 热处理, 导电率, 硬度

Abstract: Combined with the production practice of C19210 copper alloy special-shaped strip in enterprises, which consists of continuous extrusion, three-stand continuous rolling, bell-type isothermal annealing, cold rolling, continuous annealing, finishing rolling, the two annealing processes in the process scheme were studied. The results show that for the C19210 copper alloy, the first bell-type isothermal annealing at 500 ℃ for 20 h is better. After that and then cold rolling, the conductivity of the special-shaped strip is about 89%IACS and the hardness is about 120 HV0.5. However, obvious non-uniform properties between the thin part and the thick part of the strip occurs after the second continuous annealing. When isothermal annealed at 450 ℃ for 2 h, the properties of the thick and thin parts are uniform, and the conductivity of the strip after finishing rolling reaches 90.1%IACS, the hardness keeps about 120 HV0.5. Finally, the feasible preparation process of C19210 alloy special-shaped strip is adopted as follows: continuous extrusion, three-stand continuous rolling, bell-type isothermal annealing at 500 ℃for 20 h, cold rolling, isothermal annealing at 450 ℃ for 2 h, and finishing rolling.

Key words: C19210 copper alloy, special-shaped strip, heat treatment, conductivity, hardness

中图分类号:

TG146.1

张振峰, 李翰冬, 陈伟, 秦柳馨, 林高用, 姜雁斌. 异形C19210铜合金带材的热处理工艺[J]. 金属热处理, 2023, 48(10): 192-197.

Zhang Zhenfeng, Li Handong, Chen Wei, Qin Liuxin, Lin Gaoyong, Jiang Yanbin. Heat treatment process for C19210 copper alloy special-shaped strip[J]. Heat Treatment of Metals, 2023, 48(10): 192-197.

参考文献

[1]张文芹, 吕显龙, 冯小龙. 蚀刻型高密度引线框架铜合金带材的研制进展[J]. 有色金属材料与工程, 2020, 41(3): 1-6.
Zhang Wenqin, Lü Xianlong, Feng Xiaolong. Development of copper alloy strip for etched high density lead frame[J]. Nonferrous Metal Materials and Engineering, 2020, 41(3): 1-6.
[2]汪明朴, 贾延琳, 李周. 先进高强导电铜合金[M]. 长沙: 中南大学出版社, 2015.
[3]刘勇, 陆德平, 杨湘杰, 等. 热处理工艺对Cu-Fe-P 合金显微硬度及导电率的影响[J]. 金属热处理, 2004, 29(5): 35-37.
Liu Yong, Lu Deping, Yang Xiangjie, et al. Effect of heat treatment on micro-hardness and electrical conductivity of Cu-Fe-P alloy[J]. Heat Treatment of Metals, 2004, 29(5): 35-37.
[4]张御天, 张满, 付彭怀. Mg和Er对Cu-Fe-P合金组织性能的影响[J]. 金属热处理, 2006, 31(21): 68-71.
Zhang Yutian, Zhang Man, Fu Penghuai. Effect of Mg and Er on microstructure andmechanical properties of Cu-Fe-P alloy[J]. Heat Treatment of Metals, 2006, 31(21): 68-71.
[5]Geng Y F, Ban Y J, Wang B J, et al. A review of microstructure and texture evolution with nanoscale precipitates for copper alloys[J]. Journal of Materials Research and Technology, 2020, 9(5): 11918-11934.
[6]Guo F A, Xiang C J, Yang C X, et al. Study of rare earth elements on the physical and mechanical properties of a Cu-Fe-P-Cr alloy[J]. Materials Scienceand Engineering B, 2008, 147(1): 1-6.
[7]袁振宇, 董企铭, 刘平, 等. 时效对Cu-Fe-P合金显微硬度及导电率的影响[J]. 热加工工艺, 2002, 31(3): 33-34.
Yuan Zhenyu, Dong Qiming, Liu Ping, et al. The influence of aging process on the microhardness and electrical conductivity of Cu-Fe-P alloy[J]. Hot Working Technology, 2002, 31(3): 33-34.
[8]曹峰, 董琦祎, 廖开举, 等. 形变热处理对Cu-0.7Fe-0.12P合金组织和性能的影响[J]. 粉末冶金材料科学与工程, 2015, 20(3): 464-469.
Cao Feng, Dong Qiyi, Liao Kaiju, et al. Effect of thermo-mechanical treatment on microstructure and properties of Cu-0.7Fe-0.12P alloy[J]. Materials Science and Engineering of Powder, 2015, 20(3): 464-469.
[9]Dong Q Y, Shen L N, Cao F, et al. Effect of thermomechanical processing on the microstructure and properties of a Cu-Fe-P alloy[J]. Journal of Materials Engineering and Performance, 2015(4): 1531-1539.
[10]戴姣燕. 高强导电铜合金制备及其相关基础研究[D]. 长沙: 中南大学, 2009.
[11]Dong Q Y, Shen L N, Cao F, et al. Effect of thermomechanical processing on the microstructure and properties of a Cu-Fe-P alloy[J]. Journal of Materials Engineering and Performance, 2015(4): 1531-1539.
[12]Dong Q Y, Shen L N, Cao F, et al. Study of the coarsening and hardening behaviour of coherent gamma-Fe particles in Cu-2.1Fe alloy[J]. Acta Metallurgica Sinica, 2014, 50(10): 1224-1230.
[13]杨春秀, 郭富安, 向朝建, 等. 时效态Cu-Fe-P合金组织和性能的研究[J]. 特种铸造及有色合金, 2007, 27(12): 975-978, 902.
Yang Chunxiu, Guo Fuan, Xiang Chaojian, et al. Microstructure and properties of aging Cu-Fe-P alloy[J]. Special Casting and Nonferrous Alloys, 2007, 27(12): 975-978, 902.
[14]董企铭. 双重时效对Cu-Fe-P合金组织和性能的影响[C]//第三届中国热处理活动周暨第六次全国热处理生产技术改造会议论文专辑, 2005: 3.

[1]	袁志钟, 王梦飞, 张伯承, 段旭斌, 李表敏, 杨海峰, 罗锐, 程晓农. 冷作模具钢SKD11的热处理增韧技术[J]. 金属热处理, 2023, 48(9): 1-7.
[2]	王毅, 韩杰, 刘超, 邓玲蕊, 李辉, 许荣昌. DQ-T工艺对1000 MPa级高强钢组织和性能的影响[J]. 金属热处理, 2023, 48(9): 30-34.
[3]	毛福祥, 蒋邵龙, 刘伟, 束文武, 王林涛. 热处理工艺对气阀合金NCF3015组织和性能的影响[J]. 金属热处理, 2023, 48(9): 92-94.
[4]	杨赛玄, 杨晓斌, 陆盼盼, 赵倩, 董治中, 董纪. 1 T磁场下回火工艺对25CrMo48V钢耐蚀性能的影响[J]. 金属热处理, 2023, 48(9): 106-109.
[5]	黄元春, 马尚坤, 刘宇, 严积珺, 吴镇力. Gd含量对3003铝合金微观组织及导电率的影响[J]. 金属热处理, 2023, 48(9): 129-135.
[6]	戴钊, 郭智, 龙晓燕, 冯晓勇, 刘伟, 张福成, 李艳国. Si含量对高碳贝氏体钢微观组织与性能的影响[J]. 金属热处理, 2023, 48(9): 165-173.
[7]	陈海, 崔鼎. 42CrMo钢稀土微合金化对气体渗氮性能的影响[J]. 金属热处理, 2023, 48(9): 180-182.
[8]	周江, 项国东, 徐昶, 张显程, 夏咸喜, 朱保印, 赵彦芬, 金晓. 长时服役后HR3C钢析出相变化及对硬度的影响[J]. 金属热处理, 2023, 48(9): 203-207.
[9]	张志春, 温佳, 陈国瑞, 吴广辉, 翁泽钜, 顾开选. 低合金耐磨钢的热处理工艺及力学性能[J]. 金属热处理, 2023, 48(9): 220-224.
[10]	王娇娇, 刘宏春, 刘泳, 陈红卫, 田志强, 张洪起. 一种宽回火时间窗口的10.9级螺栓钢组织和性能[J]. 金属热处理, 2023, 48(9): 233-237.
[11]	张伦凤, 王治涵, 赵俊渝, 安康, 徐骏, 顾剑锋. 热处理工艺模拟专用材料数据库的设计与实现[J]. 金属热处理, 2023, 48(9): 247-252.
[12]	杨树林, 赵吉庆, 闫磊, 杨钢. эи866合金锻件径向条纹形成原因与消除工艺[J]. 金属热处理, 2023, 48(9): 279-282.
[13]	牛旭, 刘越, 王灼, 张雅静, 刘平祥. 钒含量对秸秆膨化机螺杆用Cr20高铬铸铁组织与性能的影响[J]. 金属热处理, 2023, 48(8): 8-15.
[14]	肖欣睿, 孙涛, 邓国勇, 彭洁, 苏海, 黎汝栋, 周杰, 王和斌. 添加Sc对6013铝合金组织和硬度的影响[J]. 金属热处理, 2023, 48(8): 16-23.
[15]	孙晓冉, 王程明, 赵楠, 白丽娟, 郑文跃. 4330-Nb抽油杆用钢的连续冷却转变特性分析[J]. 金属热处理, 2023, 48(8): 42-46.

异形C19210铜合金带材的热处理工艺

Heat treatment process for C19210 copper alloy special-shaped strip

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价