正火温度对G18CrMo2-6铸钢微观组织及力学性能的影响

doi:10.13251/j.issn.0254-6051.2024.01.021

金属热处理 ›› 2024, Vol. 49 ›› Issue (1): 137-141.DOI: 10.13251/j.issn.0254-6051.2024.01.021

正火温度对G18CrMo2-6铸钢微观组织及力学性能的影响

陈玉波, 王培杰, 原海瑞, 李振江

太原科技大学金属材料成形理论与技术山西省重点实验室, 山西太原 030024

收稿日期:2023-08-08 修回日期:2023-11-10 发布日期:2024-02-29
通讯作者: 李振江,副教授,博士,E-mail: lizj@tyust.edu.cn
作者简介:陈玉波(1997—),男,硕士,主要研究方向为钢铁材料热处理,E-mail:S20201401004@stu.tyust.edu.cn。
基金资助:
山西省基础研究计划(202203021211207); 山西省科技创新人才团队专项(202204051001002)

Effect of normalizing temperature on microstructure and mechanical properties of G18CrMo2-6 cast steel

Chen Yubo, Wang Peijie, Yuan Hairui, Li Zhenjiang

Shanxi Key Laboratory of Metal Forming Theory and Technology, Taiyuan University of Science and Technology, Taiyuan Shanxi 030024, China

Received:2023-08-08 Revised:2023-11-10 Published:2024-02-29

摘要/Abstract

摘要： 研究了正火温度(850~1000 ℃)对G18CrMo2-6铸钢微观组织和力学性能的影响。结果表明,尽管正火温度不同,G18CrMo2-6钢的微观组织均为贝氏体铁素体(BF)和马氏体-奥氏体(M-A)岛组成的粒状贝氏体。随着正火温度的升高,粒状贝氏体中M-A岛的数量和尺寸先减小后增加,从而导致冲击吸收能量呈先上升后下降的趋势。当正火温度低于940 ℃时,随着正火温度的升高,M-A岛数量减少,C、Cr等元素扩散到BF中,使屈服强度升高。正火温度为940 ℃时,G18CrMo2-6钢的抗拉强度和冲击吸收能量最高,分别为942 MPa和28 J。正火温度进一步提高时,BF中位错减少,晶粒粗大,导致屈服强度下降。

关键词: G18CrMo2-6钢, 正火温度, 粒状贝氏体, M-A岛

Abstract: Effect of normalizing temperature (850-1000 ℃) on microstructure and mechanical properties of G18CrMo2-6 steel was studied. The results show that the microstructure is granular bainite composed of bainite ferrite (BF) and M-A island after normalizing at different temperatures. With the increase of normalizing temperature, the quantity and size of M-A islands decreases first and then increases, so that impact absorbed energy of the steel increases first and then decreases. When the normalizing temperature below 940 ℃, with the increase of normalizing temperature, the quantity of M-A islands decreases, C, Cr and other elements spread into BF, leading to increase yield strength. When the normalizing temperature is 940 ℃, the tensile strength and impact absorbed energy of the steel are the highest, which are 942 MPa and 28 J, respectively. When the normalizing temperature is further increased, the dislocations in BF are reduced and the grains are coarsened, resulting in a decrease in yield strength.

Key words: G18CrMo2-6 steel, normalizing temperature, granular bainite, M-A islands

中图分类号:

TG142.1

陈玉波, 王培杰, 原海瑞, 李振江. 正火温度对G18CrMo2-6铸钢微观组织及力学性能的影响[J]. 金属热处理, 2024, 49(1): 137-141.

Chen Yubo, Wang Peijie, Yuan Hairui, Li Zhenjiang. Effect of normalizing temperature on microstructure and mechanical properties of G18CrMo2-6 cast steel[J]. Heat Treatment of Metals, 2024, 49(1): 137-141.

参考文献

[1]Li Zhengjing, Xiao Namin, Li Dianzhong, et al. Effect of microstructure evolution on strength and impact toughness of G18CrMo2-6 heat-resistant steel during tempering[J]. Materials Science and Engineering A, 2014, 604: 103-110.
[2]李云良, 张汉谦, 彭碧草, 等. 核电压力容器用钢的发展及研究现状[J]. 压力容器, 2010, 27(5): 36-43.
Li Yunliang, Zhang Hanqian, Peng Bicao, et al. Development and recent research of nuclear reactor pressure vessel steels[J]. Pressure Vessel Technology, 2010, 27(5): 36-43.
[3]Dai Xin, Peng Tao, Chen Yuefeng, et al. The correlation between martensite-austenite islands evolution and fatigue behavior of SA508-IV steel[J]. International Journal of Fatigue, 2020, 139: 105776.
[4]Luo Yi, Peng Jinmin, Wang Hongbin, et al. Effect of tempering on microstructure and mechanical properties of a non-quenched bainitic steel[J]. Materials Science and Engineering A, 2010, 527(15): 3433-3437.
[5]Liu Dongyu, Bai Bingzhe, Fang Hongsheng, et al. Effect of tempering temperature and carbide free bainite on the mechanical characteristics of a high strength low alloy steel[J]. Materials Science and Engineering A, 2004, 371(1/2): 40-44.
[6]蒋中华, 杜军毅, 王培, 等. M-A岛高温回火转变产物对核电SA508-3钢冲击韧性影响机制[J]. 金属学报, 2021, 57(7): 891-902.
Jiang Zhonghua, Du Junyi, Wang Pei, et al. Mechanism of improving the impact toughness of SA508-3 steel used for nuclear power by pre-transformation of M-A islands[J]. Acta Metallurgica Sinica, 2021, 57(7): 891-902.
[7]蒋中华, 王培, 李殿中, 等. 回火温度对2.25Cr-1Mo-0.25V钢粒状贝氏体显微组织和力学性能的影响[J]. 金属学报, 2015, 51(8): 925-934.
Jiang Zhonghua, Wang Pei, Li Dianzhong, et al. Effects of tempering temperature on the microstructure and mechanical properties of granular bainite in 2.25Cr-1Mo-0.25V steel[J]. Acta Metallurgica Sinica, 2015, 51(8): 925-934.
[8]Wang Yu, Xu Yunbo, Zhang Tianyu, et al. Effects of quenching temperature on bainite transformation, retained austenite and mechanical properties of hot-galvanized Q&P steel[J]. Materials Science and Engineering A, 2021, 822: 141643.
[9]Li Jiayu, Xu Yunbo, Lu Bing, et al. Improvement of strength-ductility combination in ultra-high-strength medium-Mn Q&P steel by tailoring the characteristics of martensite/retained austenite constituents[J]. Journal of Materials Research and Technology, 2022, 18: 352-369.
[10]Dong X X, Shen Y F. Improving mechanical properties and corrosion resistance of 0.5wt.%C TRIP steel by adjusting retained austenite stability and microstructural constituents[J]. Materials Science and Engineering A, 2022, 852: 143737.
[11]Ramachandran D C, Moon J, Lee C H, et al. Role of bainitic microstructures with M-A constituent on the toughness of an HSLA steel for seismic resistant structural applications[J]. Materials Science and Engineering A, 2021, 801: 140390.
[12]Bansal G K, Tripathy S, Chandan A K, et al. Influence of quenching strategy on phase transformation and mechanical properties of low alloy steel[J]. Materials Science and Engineering A, 2021, 826: 141937.
[13]石丽辉, 徐萌波. 正火对建筑用热轧20MnV钢组织与性能的影响[J]. 金属热处理, 2019, 44(7): 28-33.
Shi Lihui, Xu Mengbo. Effect of normalizing on microstructure and properties of hot rolled 20MnV steel for construction[J]. Heat Treatment of Metals, 2019, 44(7): 28-33.
[14]程晔锋, 程巨强, 冯熠婷. 正火温度对高强度贝氏体钢管组织和性能的影响[J]. 西安工业大学学报, 2020, 40(4): 428-433.
Cheng Yefeng, Cheng Juqiang, Feng Yiting. Effects of normalizing temperature on microstructure and properties of high strength bainitic steel pipe[J]. Journal of Xi'an Technological University, 2020, 40(4): 428-433.
[15]冯丹竹, 隋轶, 张宏亮, 等. 正火工艺对12Cr1MoV合金结构钢组织性能的影响[J]. 宽厚板, 2022, 28(1): 1-5.
Feng Danzhu, Sui Yi, Zhang Hongliang, et al. Effects of normalizing process on microstructure and properties of 12Cr1MoV alloy structural steel[J]. Wide and Heavy Plate, 2022, 28(1): 1-5.
[16]王小勇, 潘涛, 王华, 等. Ni-Cr-Mo-B超厚钢板表面低碳回火马氏体组织的韧性研究[J]. 金属学报, 2012, 48(4): 401-406.
Wang Xiaoyong, Pan Tao, Wang Hua, et al. Investigation of the toughness of low carbon tempered martensite in the surface of Ni-Cr-Mo-B ultra-heavy plate steel[J]. Acta Metallurgica Sinica, 2012, 48(4): 401-406.
[17]Li Zhenjiang, Liu Yujing, Zhang Ruyi, et al. Study on impact fracture behavior of G18CrMo2-6 steel after tempering[J]. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, 2021, 235(11): 2627-2636.
[18]王云龙, 余伟, 张昳, 等. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
Wang Yunlong, Yu Wei, Zhang Yi, et al. Effect of austenitizing temperature on isothermal transformation and mechanical properties of bainite steel[J]. Heat Treatment of Metals, 2022, 47(4): 80-85.
[19]Zhou S B, Hu F, Zhou W, et al. Effect of retained austenite on impact toughness and fracture behavior of medium carbon submicron-structured bainitic steel[J]. Journal of Materials Research and Technology, 2021, 14: 1021-1034.
[20]熊国源, 刘利华, 朱文涛. 奥氏体化温度对40CrNiMo钢组织和性能的影响[J]. 中国冶金, 2021, 31(7): 30-37.
Xiong Guoyuan, Liu Lihua, Zhu Wentao. Effect of austenitizing temperature on microstructure and mechanical properties of 40CrNiMo steel[J]. China Metallurgy, 2021, 31(7): 30-37.

正火温度对G18CrMo2-6铸钢微观组织及力学性能的影响

Effect of normalizing temperature on microstructure and mechanical properties of G18CrMo2-6 cast steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	谢章龙, 陈家辉, 张丙军, 陈锋. 正火温度对低温压力容器钢板组织与力学性能的影响[J]. 金属热处理, 2023, 48(9): 110-115.
[2]	鄢文泽, 闫文青, 林轩艺, 王红鸿. 铌微合金化对低合金高强钢模拟焊接热影响区粒状贝氏体相变及SH-CCT曲线的影响[J]. 金属热处理, 2023, 48(9): 150-156.
[3]	杜军毅, 朱永有, 蒋中华, 段红玲. 2.25Cr-1Mo-0.25V钢中黑色组织的形成机制及消除[J]. 金属热处理, 2023, 48(9): 271-278.
[4]	张显武, 丁雅莉, 杨卓越, 高齐, 王胜民. 改善中碳Cr-Mn-Si钢淬透性的合金化研究[J]. 金属热处理, 2023, 48(1): 112-114.
[5]	郑涛, 李永旺, 吴裕, 卓洪, 施瀚超, 刘超红. 正火温度对低活化马氏体钢组织及力学性能的影响[J]. 金属热处理, 2022, 47(12): 103-108.
[6]	田雨, 于浩. 25CrMnB履带钢冲裁断裂成因分析[J]. 金属热处理, 2021, 46(12): 282-288.
[7]	牛文明, 张贵阳, 左永平, 王涛. 18CrNiMo7-6渗碳钢等温正火新工艺探讨[J]. 金属热处理, 2021, 46(1): 84-87.
[8]	葛加林, 张骁勇, 吉玲康, 李为卫, 何小东, 陈庆龙, 于晨阳. 高温停留时间对X80管线钢焊缝粗晶区组织与性能的影响[J]. 金属热处理, 2020, 45(7): 119-123.
[9]	白若昕, 刘振宝, 曹建春, 杨哲. 正火温度对USS122G超高强度不锈钢组织及性能的影响[J]. 金属热处理, 2020, 45(11): 73-77.
[10]	匡成盛1，曹建春1，周晓龙1，雍岐龙2,田子启1. 连续冷却条件下钼对钛微合金工程机械用钢组织与性能的影响[J]. 金属热处理, 2016, 41(1): 148-152.
[11]	刘超，姜方，崔娟，段路昭. 电渣重熔H13钢锭球化退火工艺优化[J]. 金属热处理, 2015, 40(8): 120-124.
[12]	侯敬超1，计云萍1，靳晓燕1，金自力1，任慧平1, 2. 添加稀土的20MnCrNi2Mo耐磨铸钢的组织与性能[J]. 金属热处理, 2015, 40(10): 18-21.
[13]	左传付，孟亚峰，王志宏，汤峰. 14MnMoV钢沉淀硬化效应研究[J]. 金属热处理, 2014, 39(3): 126-129.
[14]	霍颜秋, 张梦贤, 王海波, 蔡培阳. 低碳20Mn2SiVB钢贝氏体相变及其TRIP效应[J]. 金属热处理, 2014, 39(10): 72-75.
[15]	彭梦都, 王立民, 张希俊, 刘正东, 杨钢, 雷玖芳. 回火温度对45CrMoVE钢组织与性能的影响[J]. 金属热处理, 2014, 39(10): 101-104.