特大铁路钢梁桥调平垫片用Q235钢的C-N-O-S多元共渗及组织性能演变

doi:10.13251/j.issn.0254-6051.2024.05.044

金属热处理 ›› 2024, Vol. 49 ›› Issue (5): 260-266.DOI: 10.13251/j.issn.0254-6051.2024.05.044

特大铁路钢梁桥调平垫片用Q235钢的C-N-O-S多元共渗及组织性能演变

张敏敏¹, 王殿堂², 李江涛³, 王忠军², 张纪兵⁴, 张强¹, 魏胜民¹, 张琪⁵, 李建国¹

1.中国铁路济南局集团有限公司科学技术研究所, 山东济南 250001;
2.中国铁路济南局集团有限公司工务部, 山东济南 250001;
3.中国铁路济南局集团有限公司科信部, 山东济南 250001;
4.中国铁路济南局集团有限公司聊城工务段, 山东聊城 252004;
5.中国铁道科学研究院集团有限公司铁道科学技术研究发展中心, 北京 100081

收稿日期:2023-11-05 修回日期:2024-02-01 出版日期:2024-05-25 发布日期:2024-06-28
作者简介:张敏敏(1989—)，男，工程师，硕士，主要研究方向为轨道交通材料、焊接、表面技术与无损检测，E-mail:306942844@qq.com。
基金资助:
中国国家铁路集团有限公司科技开发计划(N2022B004);中国铁路济南局集团有限公司科技研究开发计划(2022G11,2024G13)

C-N-O-S multi-element co-infiltration and evolution of microstructure and properties of Q235 steel for leveling gaskets of extra-large railway steel beam bridges

Zhang Minmin¹, Wang Diantang², Li Jiangtao³, Wang Zhongjun², Zhang Jibing⁴, Zhang Qiang¹,Wei Shengmin¹, Zhang Qi⁵, Li Jianguo¹

1. Technology Research Institute, China Railway Jinan Group Co., Ltd., Jinan Shandong 250001, China;
2. Works Department of China Railway Jinan Group Co., Ltd., Jinan Shandong 250001, China;
3. Science and Information Department of China Railway Jinan Group Co., Ltd., Jinan Shandong 250001, China;
4. Liaocheng Railway Section of China Railway Jinan Group Co., Ltd., Liaocheng Shandong 252004, China;
5. Railway Science & Technology & Development Center, China Academy of Railway Sciences Co., Ltd., Beijing 100081, China

Received:2023-11-05 Revised:2024-02-01 Online:2024-05-25 Published:2024-06-28

摘要/Abstract

摘要： 为有效延长钢梁桥Q235钢调平垫片的服役寿命,采用C-N-O-S多元共渗技术进行改性处理,研究了不同参数耦合对改性层组织、硬度、耐磨性及耐候性的影响。结果表明,改性层多层结构与共渗温度有关,在640 ℃与650 ℃之间存在临界值,临界温度以下由化合物层、扩散层及氧化层组成,当超过临界温度时,由化合物层和氧化层组成。改性层厚度受共渗温度、氨气及催渗剂影响机制不同,共渗温度及氨气流量对渗层各层结构均有影响,扩散层受催渗剂流量作用明显;改性层硬度是基材的2~3倍,三层结构渗层硬度由表层向基材不断降低;两层结构化合物层的硬度均匀,在界面区硬度陡降。改性层摩擦因数最低为0.2468,约为基材的1/3。改性层自腐蚀电位最高达-0.4845 V,自腐蚀电流密度最低为1.187×10^-6mA/cm²,较基体降低2个数量级。

关键词: 铁路钢梁桥调平钢垫片, 服役寿命, 多元共渗, 组织性能

Abstract: In order to effectively extend the service life of Q235 steel beam bridge leveling gaskets, the surface modification of C-N-O-S multi-element infiltration technology was carried out. The effect of different parameters coupling on the microstructure, hardness, wear resistance and weather resistance of the modified layer was studied. The results show that the multi-layer structure of the modified layer is related to co-infiltration temperature, and there is a critical value between 640 ℃ and 650 ℃, below the critical temperature, it is composed of the compound layer, diffusion layer and oxidation layer. When the critical temperature is exceeded, the modified layer comprises compound and oxidation layers. The thickness of the modified layer is affected by co-infiltration temperature, ammonia and infiltration promoting agent flow rates, and the temperature and ammonia flow rate affect the structure of each layer. The infiltration promoting agent flow rate has an obvious effect on the diffusion layer. The hardness of the modified layer is 2-3 times of that of the substrate, the hardness of the three-layer structural layer decreases continuously from the surface to substrate. The hardness of the two-layer structural compound layer is uniform, with sharp decrease in hardness in the interface area. The lowest friction coefficient of the modified layer is 0.2468, which is about 1/3 of the base material. The highest free-corrosion potential of the modified layer is -0.4845 V, and the lowest free corrosion current density is 1.187×10^-6 mA/cm², which is reduced by 2 orders of magnitude compared to the substrate.

Key words: leveling steel gaskets for railway steel beam bridge, service life, multi-element co-infiltration, microstructure and properties

中图分类号:

张敏敏, 王殿堂, 李江涛, 王忠军, 张纪兵, 张强, 魏胜民, 张琪, 李建国. 特大铁路钢梁桥调平垫片用Q235钢的C-N-O-S多元共渗及组织性能演变[J]. 金属热处理, 2024, 49(5): 260-266.

Zhang Minmin, Wang Diantang, Li Jiangtao, Wang Zhongjun, Zhang Jibing, Zhang Qiang,Wei Shengmin, Zhang Qi, Li Jianguo. C-N-O-S multi-element co-infiltration and evolution of microstructure and properties of Q235 steel for leveling gaskets of extra-large railway steel beam bridges[J]. Heat Treatment of Metals, 2024, 49(5): 260-266.

参考文献

[1]Abutorabian E, Dehkordi M R. Numerical study of seismic response of irregular multi-frame reinforced concrete bridges[J]. Proceedings of the Institution of Civil Engineers, 2021, 173(11): 783-789.
[2]Sajed M, Tehrani P. Investigating the effects of combinations of irregularities on seismic ductility demands and mean response for four-span RC bridges considering displacement direction[J]. Bridge Structures, 2020, 16: 105-117.
[3]Maleki-amin M J, Maalek K S. Regularity classification and corresponding analysis method requirements of horizontally curved bridges with unequal pier heights[J]. Earthquake Engineering and Engineering Vibration, 2023, 22(2): 549-571.
[4]禚一, 王旭, 张军. 高速铁路沉降自动化监测系统SMAIS的研发及应用[J]. 铁道工程学报, 2015, 32(4): 10-15.
Zhuo Yi, Wang Xu, Zhang Jun. Development and application of automatic monitoring system SMAIS for settlement of high-speed railway[J]. Journal of Railway Engineering Society, 2015, 32(4): 10-15.
[5]Sim S, Cole I S, Bocher F, et al. Investigating the effect of salt and acid impurities in supercritical CO₂ as relevant to the corrosion of carbon capture and storage pipelines[J]. International Journal of Greenhouse Gas Control, 2013, 17: 534-541.
[6]姜军, 王军阳, 金武俊, 等. 带肋钢腐蚀及其防腐蚀技术研究进展[J]. 中国腐蚀与防护学报, 2021, 41(4): 339-449.
Jiang Jun, Wang Junyang, Jin Wujun, et al. Research progress on corrosion and anti-corrosion technology of ribbed steel[J]. Journal of Chinese Society for Corrosion and Protection, 2021, 41(4): 339-449.
[7]Yuan W Y, Li R F, Chen Z H, et al. A comparative study on microstructure and properties of traditional laser cladding and high-speed laser cladding of Ni45 alloy coatings[J]. Surface and Coatings Technology, 2020, 405(12): 65-82.
[8]Ren X, Zhao R S, Wang W, et al. Corrosion resistance of TiCN films prepared with combining multi-arcion plating and magnetron sputtering technique[J]. Rare Metal Materials and Engineering, 2018, 47(7): 2028-2036.
[9]Krellina P, Almeida E A S, Milan J C G, et al. Microstructural and tribological characterization of niobium boride coating produced on AISI 1020 steel via multicomponent boriding[J]. Materials Research Express, 2020, 7(2): 026413.
[10]Wu D, Kahn H, Dalton J C, et al. Orientation dependence of nitrogen supersaturation in austenitic stainless steel during low-temperature gas-phase nitriding[J]. Acta Materialia, 2014, 79: 339-350.
[11]蒋小龙. 50CrVA钢亚温淬火和多元共渗复合工艺及组织性能探索[D]. 成都: 西南交通大学, 2012.
[12]杨强云. 新型高耐腐蚀、高抗疲劳、高强紧固件工艺探究与组织性能分析[D]. 成都: 西南交通大学, 2016.
[13]章敬保. Fe-N化合物与复合处理层抗腐蚀机理及纽织性能研究[D]. 成都: 西南交通大学, 2017.
[14]Chen X, Wang Y, Xie W Z, et al. Fabrication and corrosion resistance of super-thick compound layer by austenitic gas oxynitrocarburizing[J]. Journal of Alloys and Compounds, 2018, 765: 1099-1110.
[15]Zhang J W, Lu L T, Cui G D, et al. Effect of process temperature on the microstructure and properties of gas oxynitrocarburized 35CrMo alloy steel[J]. Materials & Design, 2010, 35(5): 2654-2658.
[16]Kucharska B, Michalski I J, Wojcik G. Mechanical and microstructural aspects of C20-steel blades subjected to gas nitriding[J]. Archives of Civil and Mechanical Engineering, 2019, 19(1): 147-156.
[17]张鹏飞. 低温气体多元共渗超厚化合物层工艺组织性能及应用研究[D]. 成都: 西南交通大学, 2016.
[18]Gronostajski Z, Widomask P, Kaszuba M, et al. Influence of the phase structure of nitrides and properties of nitrided layers on the durability of tools applied in hot forging processes[J]. Journal of Manufacturing Processes, 2020, 52: 247-262.
[19]廖斌, 刘晗, 范琪, 等. 42CrMo钢离子氮碳氧多元共渗及动力学分析[J]. 材料热处理学报, 2016, 37(8): 184-188.
Liao Bin, Liu Han, Fan Qi, et al. Plasma oxynitrocarburising of 42CrMo steel and kinetics analysis[J]. Transactions of Materials and Heat Treatment, 2016, 37(8): 184-188.
[20]Sree K R, Reddy G K, Prasanna G L, et al. Dry sliding wear behavior of treated AISI 304 stainless steel by gas nitriding processes[J]. Materials Today Proceeding, 2021, 44: 1406-1411.
[21]李毅丰, 柴均博, 李赛鹏, 等. 催渗剂对O-N-C多元共渗Q235钢耐蚀性的影响[J]. 金属热处理, 2013, 38(1): 80-83.
Li Yifeng, Chai Junbo, Li Saipeng, et al. Effect of additives on corrosion resistance of Q235 steel by oxynitrocarburizing[J]. Heat Treatment of Metals, 2013, 38(1): 80-83.
[22]章敬保, 杨川, 张程菘, 等. 气体氮化对碳钢耐蚀性的影响及化合物层的价电子理论分析[J]. 腐蚀与防护, 2018, 39(3): 207-212.
Zhang Jingbao, Yang Chuan, Zhang Chengsong, et al. Effect of gas nitriding on the corrosion resistance of carbon steel and empirical electron theory analysis of compound layer[J]. Corrosion and Protection, 2018, 39(3): 207-212.

特大铁路钢梁桥调平垫片用Q235钢的C-N-O-S多元共渗及组织性能演变

C-N-O-S multi-element co-infiltration and evolution of microstructure and properties of Q235 steel for leveling gaskets of extra-large railway steel beam bridges

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	孙进宝, 王少华, 刘惠, 李国爱, 王海龙, 张景亮, 周志宇. 稳定化退火对新型5×××铝合金组织与性能的影响[J]. 金属热处理, 2024, 49(4): 175-182.
[2]	王哲昊. 金属钽表面处理工艺进展[J]. 金属热处理, 2024, 49(2): 259-264.
[3]	陈文涛, 尹靖, 王春艳, 胡桂领. 激光增材制造6061铝合金热处理及强韧机理[J]. 金属热处理, 2023, 48(8): 172-178.
[4]	黄志国, 曹永政, 李艳艳, 蒋波. 10.9级紧固件用贝氏体型非调质冷镦钢的研究现状[J]. 金属热处理, 2023, 48(8): 219-224.
[5]	王天娇, 丁小明, 庄欠玉, 蒋波. 温成形高铁弹条用38Si7弹簧钢热处理后的组织性能[J]. 金属热处理, 2023, 48(11): 112-119.
[6]	郑革, 陈杰, 牛堃宁, 林建国, 檀朝桂, 戴翌龙. Cu含量及T6处理对电力金具用铝合金组织性能的影响[J]. 金属热处理, 2022, 47(8): 217-222.
[7]	樊帅奇, 李海涛, 王雪松, 张蕾涛, 徐金富, 戴姣燕. 放电等离子烧结CuIn₅合金的工艺优化[J]. 金属热处理, 2022, 47(7): 76-80.
[8]	黄龙, 邓想涛, 王昭东. 回火温度对颗粒增强型低合金耐磨钢组织和性能的影响[J]. 金属热处理, 2022, 47(3): 1-6.
[9]	刘鹏飞, 杨波, 陈宇, 刘宏亮. 退火工艺对980 MPa级热镀锌双相钢组织及性能的影响[J]. 金属热处理, 2022, 47(11): 122-125.
[10]	李敏娜, 马保飞, 郭金明, 吴晨, 肖松涛. 高强韧TB8钛合金的热处理制度[J]. 金属热处理, 2021, 46(9): 116-119.
[11]	吴昊, 邓想涛, 李成儒, 隋轶, 张涛, 纪汶伯, 王昭东. 耐磨钢NM400冷弯开裂分析[J]. 金属热处理, 2021, 46(9): 262-267.
[12]	花思明, 张平则, 刘子利. CuCr1合金接触线的时效工艺及组织性能[J]. 金属热处理, 2021, 46(5): 143-149.
[13]	王思成, 周丹, 柴希阳, 佟石, 杨洋, 王天琪. 控轧控冷工艺对440 MPa级船体钢组织与性能的影响[J]. 金属热处理, 2021, 46(4): 138-142.
[14]	陈卓, 王诚斯, 靳斌, 刘靖宝, 郝雷, 邝霜, 王金荣. 980 MPa级冷轧复相钢力学性能的多元调控[J]. 金属热处理, 2021, 46(4): 157-160.
[15]	石晓霞, 任慧平, 李晓, 王超, 宫鑫. 26CrMoVNbRE钢高效热处理调质工艺边界探索[J]. 金属热处理, 2021, 46(3): 39-45.