V+Ti微合金化Mn-Cr系贝氏体型非调质钢的氢脆敏感性

doi:10.13251/j.issn.0254-6051.2024.07.016

金属热处理 ›› 2024, Vol. 49 ›› Issue (7): 106-112.DOI: 10.13251/j.issn.0254-6051.2024.07.016

V+Ti微合金化Mn-Cr系贝氏体型非调质钢的氢脆敏感性

周蕾¹, 王莹¹, 张永健², 赵晓丽², 惠卫军²

1.南钢钢铁股份有限公司特钢事业部, 江苏南京 210035;
2.北京交通大学机械与电子控制工程学院, 北京 100044

收稿日期:2023-12-22 修回日期:2024-04-02 出版日期:2024-07-25 发布日期:2024-08-29
通讯作者: 惠卫军,教授,E-mail: wjhui@bjtu.edu.cn
作者简介:周蕾(1980—),男,高级工程师,博士,主要研究方向为汽车用特殊钢产品研发,E-mail: zhoulei1@njsteel.com.cn。
基金资助:
国家重点研发计划(2016YFB0300100)

Hydrogen embrittlement of V+Ti microalloyed Mn-Cr bainitic forging steel

Zhou Lei¹, Wang Ying¹, Zhang Yongjian², Zhao Xiaoli², Hui Weijun²

1. Special Steels Division, Nanjing Iron & Steel Co., Ltd., Nanjing Jiangsu 210035, China;
2. School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044, China

Received:2023-12-22 Revised:2024-04-02 Online:2024-07-25 Published:2024-08-29

摘要/Abstract

摘要： 利用电化学预充氢、慢应变速率拉伸和氢热分析试验,结合SEM、TEM及EBSD微观组织分析,对比研究了一种V+Ti微合金化Mn-Cr系贝氏体型非调质钢在锻态和500 ℃回火态的氢逸出行为及氢脆敏感性。结果表明,具有粒状贝氏体组织的锻态试样经500 ℃处理后块状M/A组元分解,并析出纳米级细小的(V, Ti)(C, N)和渗碳体,这使得回火态试样的抗拉强度降低而屈服强度显著提高。锻态和回火态试样预充氢吸附的氢主要为可扩散性氢,回火态试样中吸附的氢含量略低于锻态试样。以相对缺口抗拉强度降低表征的氢脆敏感性指数由锻态试样的31.8%降低为回火态试样的12.8%,500 ℃回火处理引起的微观组织变化是回火态试样具有优异抗氢脆性能的主要原因。

关键词: 贝氏体型非调质钢, 粒状贝氏体, 氢脆, 回火, 微观组织

Abstract: Hydrogen desorption and hydrogen embrittlement (HE) behavior of a V+Ti microalloyed Mn-Cr bainitic forging steel in the as-forged and 500 ℃ tempered conditions were studied by using electrochemical pre-hydrogen-charging, hydrogen thermal analysis (TDA) and slow strain rate tensile (SSRT) testing combined with SEM, TEM and EBSD microstructural analyses. The results show that the blocky martensite/austenite (M/A) constituents decompose with the precipitation of nano-sized (V,Ti)(C,N) and cementite particles, which causes a decrease of tensile strength while a significant increase of yield strength. The result of TDA reveals that most of absorbed hydrogen is diffusible hydrogen and the hydrogen content in the tempered specimen is slightly lower than that of the as-forged specimen. The HEI expressed by the relative loss of notch tensile strength before and after hydrogen-charging significantly decreases from 31.8% for the as-forged specimen to 12.8% for the tempered specimen, which is mainly due to the microstructural changes caused by the tempering treatment.

Key words: bainitic forging steel, granular bainite, hydrogen embrittlement, tempering, microstructure

中图分类号:

TG142.1

周蕾, 王莹, 张永健, 赵晓丽, 惠卫军. V+Ti微合金化Mn-Cr系贝氏体型非调质钢的氢脆敏感性[J]. 金属热处理, 2024, 49(7): 106-112.

Zhou Lei, Wang Ying, Zhang Yongjian, Zhao Xiaoli, Hui Weijun. Hydrogen embrittlement of V+Ti microalloyed Mn-Cr bainitic forging steel[J]. Heat Treatment of Metals, 2024, 49(7): 106-112.

参考文献

[1]陈思联, 惠卫军, 王连海, 等. 节能低成本高品质非调质钢的研发[J]. 钢铁, 2014, 49(6): 1-7.
Chen Silian, Hui Weijun, Wang Lianhai, et al. Research and development of energy-saving high performance microalloyed forging steels[J]. Iron and Steel, 2014, 49(6): 1-7.
[2]陈蕴博, 马鸣图, 王国栋. 汽车用非调质钢的研究进展[J]. 中国工程科学, 2014, 16(2): 4-17.
Chen Yunbo, Ma Mingtu, Wang Guodong, et al. Resent progress of non-quenched and tempered steel for automotive sheet[J]. Strategic Study of CAE, 2014, 16(2): 4-17.
[3]周蕾, 魏刚武, 高延详, 等. 30MnVS非调质钢的开发[J]. 钢铁, 2017, 52(3): 76-81.
Zhou Lei, Wei Gangwu, Gao Yanxiang, et al. Development of 30MnVS non-quenched and tempered steel[J]. Iron and Steel, 2017, 52(3): 76-81.
[4]Buchmayr B. Critical assessment 22: Bainitic forging steels[J]. Materials Science and Technology, 2016, 32(6): 517-522.
[5]Sourmail T, Smanio V. Optimisation of the mechanical properties of air cooled bainitic steel components through tailoring of the transformation kinetics[J]. Materials Science and Engineering A, 2013, 582: 257-261.
[6]Citti P, Giorgetti A, Millefanti U. Mechanical characterization of a new low carbon bainitic steel for high performance crankshaft[J]. Procedia Structural Integrity, 2018, 12: 438-447.
[7]Elek L, Wagener R, Kaufmann H, et al. New bainitic steel for cyclic loaded safety parts with improved cyclic material behaviour[J]. Procedia Engineer, 2015, 101: 151-158.
[8]张继魁, 董伦, 辛莹, 等. 低碳Mn-B贝氏体钢在汽车前轴上的应用试验[J]. 机械工程材料, 2003, 27(7): 42-44.
Zhang Jikui, Dong Lun, Xin Ying, et al. Application of low carbon Mn-B bainitic steel to automobile front axle[J]. Materials for Mechanical Engineering, 2003, 27(7): 42-44.
[9]冯佳奇, 王敢利, 邹敏华, 等. 重型汽车前轴用非调质钢的研究[J]. 汽车工艺与材料, 2014(4): 1-7.
[10]安治国, 黄艳新, 侯环宇, 等. 汽车前轴用贝氏体型非调质钢连续冷却转变[J]. 钢铁, 2016, 51(12): 70-73.
An Zhiguo, Huang Yanxin, Hou Huanyu, et al. Continuous cooling transformation of bainite non-quenched and tempered steel for automobile front axle[J]. Iron and Steel, 2016, 51(12): 70-73.
[11]王占花, 惠卫军, 谢志奇, 等. 回火对钒钛微合金化Mn-Cr系贝氏体型非调质钢组织和性能的影响[J]. 金属学报, 2020, 56(11): 1141-1151.
Wang Zhanhua, Hui Weijun, Xie Zhiqi, et al. Effects of tempering temperature on microstructure and mechanical properties of a Mn-Cr type bainitic forging steel[J]. Acta Metallurgica Sinica, 2020, 56(11): 1141-1151.
[12]Hui W J, Wang Z H, Xu Z B, et al. Hydrogen embrittlement of a microalloyed bainitic forging steel[J]. Journal of Iron and Steel Research International, 2019, 26: 1011-1021.
[13]Hui W J, Xu Z B, Zhang Y J, et al. Hydrogen embrittlement behavior of high strength rail steels: A comparison between pearlitic and bainitic microstructure[J]. Materials Science and Engineering A, 2017, 704: 199-206.
[14]Zhang Y J, Xu Z B, Zhao X L, et al. Hydrogen embrittlement behavior of high strength bainitic rail steel: Effect of tempering treatment[J]. Engineering Failure Analysis, 2018, 93: 100-110.
[15]Takai K, Watanuki R. Hydrogen in trapping states innocuous to environmental degradation of high-strength steels[J]. ISIJ International, 2003, 43(4): 520-526.
[16]Lovicu G, Bottazzi M, D'aiuto F, et al. Hydrogen embrittlement of automotive advanced high-strength steels[J]. Metallurgical and Materials Transaction A, 2012, 43: 4075-4087.
[17]Zhu X, Zhang K, Li W, et al. Effect of retained austenite stability and morphology on the hydrogen embrittlement susceptibility on quenching and partioning treated steels[J]. Materials Science and Engineering A, 2016, 658: 400-408.
[18]Shi X B, Yan W, Wang W, et al. HIC and SCC behavior of high-strength pipeline steels[J]. Acta Metallurgica Sinica, 2015, 28: 799-808.
[19]Shim D H, Lee T, Lee J, et al. Increased resistance to hydrogen embrittlement in high-strength steels composed of granular bainite[J]. Materials Science and Engineering A, 2017, 700: 473-480.
[20]Luo Y, Peng J M, Wang H B, et al. Effect of tempering on microstructure and mechanical properties of a non-quenched bainitic steel[J]. Materials Science and Engineering A, 2010, 527: 3433-3437.
[21]Lan H F, Du L X, Misra R D K. Effect of microstructural constituent on strength-toughness combination in a low carbon bainitic steel[J]. Materials Science and Engineering A, 2014, 611: 194-200.
[22]Ryu J Y, Chun Y S, Lee C S, et al. Effect of deformation on hydrogen trapping and effusion in TRIP-assisted steel[J]. Acta Materialia, 2012, 60: 4085-4092.
[23]王贞, 刘静, 黄峰, 等. 回火温度对DP600钢氢扩散及氢脆敏感性的影响[J]. 金属热处理, 2021, 46(2): 87-94.
Wang Zhen, Liu Jing, Huang Feng, et al. Effect of tempering temperature on hydrogen diffusion and hydrogen embrittlement susceptibility of DP600 steel[J]. Heat Treatment of Metals, 2021, 46(2): 87-94.
[24]Zafra A, Peral L B, Belzunce J, et al. Effect of hydrogen on the tensile properties of 42CrMo4 steel quenched and tempered at different temperatures[J]. International Journal of Hydrogen Energy, 2018, 43: 9068-9082.
[25]Lee J, Lee T, Kwon Y J, et al. Effects of vanadium carbides on hydrogen embrittlement of tempered martensitic steel[J]. Metals and Materials International, 2016, 22(3): 364-372.

V+Ti微合金化Mn-Cr系贝氏体型非调质钢的氢脆敏感性

Hydrogen embrittlement of V+Ti microalloyed Mn-Cr bainitic forging steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	陈保安, 李梦琳, 陈瑞, 多俊龙, 韩钰, 祝志祥, 杨长龙, 缪姚军. 添加稀土对Al-Mg-Si合金微观组织和性能的影响[J]. 金属热处理, 2024, 49(7): 100-105.
[2]	蒋军杰, 王永彪, 肖志玲, 樊江磊, 张正文. 退火温度对激光选区熔化成形TA15钛合金微观组织与力学性能的影响[J]. 金属热处理, 2024, 49(7): 241-248.
[3]	丁屹, 李爱国, 李贤君, 白玉宏, 蒋秋娥, 彭光华, 罗平, 侯俊卿. 热处理工艺对8 mm厚TC4钛合金板微观组织和强度的影响[J]. 金属热处理, 2024, 49(7): 261-266.
[4]	蒙品品, 张晓波. 退火处理对纯铜微观组织及力学性能的影响[J]. 金属热处理, 2024, 49(7): 267-273.
[5]	刘阳, 高茗, 马莉, 胡祯, 孙中梅, 张士震. 低成本无钒热轧钢筋HRB400E的生产工艺优化[J]. 金属热处理, 2024, 49(7): 294-300.
[6]	艾根根, 姜凤阳, 思芳, 刘江南, 卫娜, 王俊勃. 退火工艺对高锰TWIP钢组织及耐蚀性能的影响[J]. 金属热处理, 2024, 49(7): 313-321.
[7]	赵希庆, 王付杰, 张丙军. 回火对直接淬火A387Gr11CL2钢板组织和性能的影响[J]. 金属热处理, 2024, 49(7): 322-325.
[8]	张新宇, 隋欣, 罗旭东, 程素玲, 张义, 陈金生, 张伟. 汽车用6014铝合金冷轧板的热处理工艺[J]. 金属热处理, 2024, 49(7): 331-335.
[9]	刘怡然, 李磊. 退火工艺对SLM AlSi10Mg合金拉伸变形行为的影响[J]. 金属热处理, 2024, 49(6): 23-28.
[10]	于毫勇, 吕明奎, 凡艳丽, 刘瑞德. 基于水溶性淬火液的铁路扣件II型弹条热处理工艺[J]. 金属热处理, 2024, 49(6): 91-95.
[11]	薛峰, 耿志宇, 刘旭明, 毕廉, 周天鹏. 高强双相钢DP980成形极限性能及微观组织分析[J]. 金属热处理, 2024, 49(6): 164-168.
[12]	钟振东, 樊金桃, 王付胜, 陈亚军. 电磁场对铝合金组织及性能影响的研究进展[J]. 金属热处理, 2024, 49(6): 261-269.
[13]	宋全, 曹辉辉, 张甜琪, 淡婷, 马芳, 张影. 液压工装螺栓断裂失效分析[J]. 金属热处理, 2024, 49(6): 301-304.
[14]	郭炜, 管博, 陈威, 吴丹. 多次闭模压缩对不同Si含量AZ31合金显微组织和耐磨性能的影响[J]. 金属热处理, 2024, 49(5): 36-39.
[15]	王泽龙, 冯兆龙, 李伟, 孙思博. 冷塑性变形及退火工艺对Ti45Nb合金组织和性能的影响[J]. 金属热处理, 2024, 49(5): 112-117.