PH13-8Mo不锈钢带状偏析及其在热处理中的演变

doi:10.13251/j.issn.0254-6051.2024.07.023

金属热处理 ›› 2024, Vol. 49 ›› Issue (7): 152-156.DOI: 10.13251/j.issn.0254-6051.2024.07.023

PH13-8Mo不锈钢带状偏析及其在热处理中的演变

陈素明¹, 岳珊¹, 胡生双¹, 赵虎¹, 李毅¹, 吴海峰¹, 欧阳德来²

1.中航西安飞机工业集团股份有限公司, 陕西西安 710089;
2.南昌航空大学材料科学与工程学院, 江西南昌 330063

收稿日期:2024-02-06 修回日期:2024-05-08 出版日期:2024-07-25 发布日期:2024-08-29
通讯作者: 欧阳德来,教授,E-mail:ouyangdelai@163.com
作者简介:陈素明(1978—),男,研究员级高级工程师,主要研究方向为特种工艺制造,E-mail:mhgy_syfh@163.com。
基金资助:
江西省自然科学基金(20224BAB204013)

Strip segregation in PH13-8Mo stainless steel and its evolution during heat treatment

Chen Suming¹, Yue Shan¹, Hu Shengshuang¹, Zhao Hu¹, Li Yi¹, Wu Haifeng¹, Ouyang Delai²

1. AVIC Xi'an Aircraft Industry Group Co., Ltd., Xi'an Shaanxi 710089, China;
2. School of Materials Science and Engineering, Nanchang Hangkong University, Nanchang Jiangxi 330063, China

Received:2024-02-06 Revised:2024-05-08 Online:2024-07-25 Published:2024-08-29

摘要/Abstract

摘要： 以某PH13-8Mo不锈钢轴零件为研究对象,研究了PH13-8Mo不锈钢带状偏析组织特征及其在固溶时效处理中的演变。结果表明,PH13-8Mo不锈钢中存在成分偏析带和δ铁素体偏析带两种类型带状偏析,成分偏析带呈平直连续状分布,δ铁素体偏析带呈平直不连续状分布。成分偏析带中Ni元素正偏析、Fe元素负偏析,Ni、Fe含量分别为11%和72%,分别低于和高于钢中Ni、Fe元素含量。δ铁素体偏析带中Ni、Fe含量分别为4%和71%,均低于钢中Ni、Fe平均含量;Cr、Mo、Al含量分别为17%、4.5%和1.84%,均高于钢中Cr、Mo、Al平均含量。1100 ℃×2 h固溶+540 ℃×4 h时效可有效消除PH13-8Mo不锈钢成分偏析带,但对δ铁素体偏析带消除作用影响不明显。

关键词: PH13-8Mo不锈钢, 带状偏析, 固溶时效

Abstract: Taking a PH13-8Mo stainless steel shaft part as the research object, the microstructure characteristics of strip segregation in the PH13-8Mo stainless steel and its evolution during solution treatment and aging were studied. The results show that there exist two types of strip segregation in the microstructure of the steel, namely component segregation strip and δ-ferrite segregation strip. The component segregation strip distributes in a straight and continuous pattern, but the δ-ferrite segregation strip distributes in a straight and discontinuous pattern. In the component segregation strip with positive segregation of Ni and negative segregation of Fe, the content of Ni and Fe is 11% and 72%, respectively, lower and higher than the content of Ni and Fe elements in the steel. In the δ-ferrite segregation strip, the content of Ni and Fe is 4% and 71%, respectively, which are lower than the average content of Ni and Fe in the steel, the content of Cr, Mo and Al is 17%, 4.5% and 1.84%, respectively, which are higher than the average content of Cr, Mo and Al in the steel. The component segregation strip in the PH13-8Mo stainless steel can be effectively eliminated by solution treatment at 1100 ℃ for 2 h and then aging at 540 ℃ for 4 h, but the δ-ferrite segregation strip can not be effectively eliminated.

Key words: PH13-8Mo stainless steel, strip segregation, solution treatment and aging

中图分类号:

TG142.1

陈素明, 岳珊, 胡生双, 赵虎, 李毅, 吴海峰, 欧阳德来. PH13-8Mo不锈钢带状偏析及其在热处理中的演变[J]. 金属热处理, 2024, 49(7): 152-156.

Chen Suming, Yue Shan, Hu Shengshuang, Zhao Hu, Li Yi, Wu Haifeng, Ouyang Delai. Strip segregation in PH13-8Mo stainless steel and its evolution during heat treatment[J]. Heat Treatment of Metals, 2024, 49(7): 152-156.

参考文献

[1]舒小勇, 鲁世强, 李贵发, 等. PH13-8Mo不锈钢热变形行为研究[J]. 特种铸造及有色合金, 2018, 38(11): 1182-1185.
Shu Xiaoyong, Lu Shiqiang, Li Guifa, et al. Hot deformation behavior of PH13-8Mo stainless steel[J]. Special Casting and Nonferrous Alloys, 2018, 38(11): 1182-1185.
[2]梁剑雄, 王长军, 高韩蓉, 等. 时效处理对PH13-8Mo高强不锈钢耐局部腐蚀行为的电化学研究[J]. 腐蚀科学与防护技术, 2017, 29(4): 407-412.
Liang Jianxiong, Wang Changjun, Gao Hanrong, et al. Effect of aging treatment on pitting corrosion resistance of PH13-8Mo stainless steel[J]. Corrosion Science and Protection Technology, 2017, 29(4): 407-412.
[3]杨凯, 朱宏伟, 于利民, 等. 时效时间对PH13-8Mo不锈钢组织和力学性能的影响[J]. 金属热处理, 2023, 48(3): 100-103.
Yang Kai, Zhu Hongwei, Yu Limin, et al. Effect of aging time on microstructure and mechanical properties of PH13-8Mo stainless steel[J]. Heat Treatment of Metals, 2023, 48(3): 100-103.
[4]Li X F, Zhang J, Akiyama E, et al. Effect of heat treatment on hydrogen-assisted fracture behavior of PH13-8Mo steel[J]. Corrosion Science, 2017, 128(11): 198-212.
[5]李雪莹, 吴钱林, 范春华, 等. 含H₂S的NaCl溶液中溶解氧对PH13-8Mo钢腐蚀性能的影响[J]. 材料科学与工艺, 2019, 27(3): 8-15.
Li Xueying, Wu Qianlin, Fan Chunhua, et al. Effect of dissolved oxygen in NaCl solution containing H₂S on the corrosion performance of PH13-8Mo steel[J]. Materials Science and Technology, 2019, 27(3): 8-15.
[6]Rosenauer A, Brandl D, Ressel G, et al. Influence of delta ferrite on the impact toughness of a PH13-8Mo maraging steel[J]. Materials Science and Engineering A, 2022, 856: 144024.
[7]程志伟, 金建军, 鲁世强, 等. 热处理工艺对PH13-8Mo钢的组织和性能的影响[J]. 材料热处理学报, 2013, 34(11): 48-54.
Cheng Zhiwei, Jin Jianjun, Lu Shiqiang, et al. Effect of heat treatment process on microstructure and properties of PH13-8Mo steel[J]. Transactions of Materials and Heat Treatment, 2013, 34(11): 48-54.
[8]张良, 雍岐龙, 梁剑雄, 等. PH13-8Mo高强不锈钢在不同温度时效后的析出相及其对力学性能的影响[J]. 机械工程材料, 2017, 41(3): 19-23, 28.
Zhang Liang, Yong Qilong, Liang Jianxiong, et al. Precipitated phases and effects of they on mechanical properties of PH13-8Mo high strength stainless steel after aging at different temperatures[J]. Materials for Mechanical Engineering, 2017, 41(3): 19-23, 28.
[9]刘杰, 叶茂, 姜枫, 等. 固溶后冷处理对PH13-8Mo马氏体不锈钢组织及性能的影响[J]. 金属热处理, 2018, 43(2): 156-159.
Liu Jie, Ye Mao, Jiang Feng, et al. Effect of cryogenic treatment after solution on microstructure and mechanical properties of PH13-8Mo martensiticstainless steel[J]. Heat Treatment of Metals, 2018, 43(2): 156-159.
[10]张湛, 薛春, 黄春波, 等. 时效温度对PH13-8Mo不锈钢组织和力学性能的影响[J]. 机械工程材料, 2014, 38(11): 72-75.
Zhang Zhan, Xue Chun, Huang Chunbo, et al. Effects of aging temperature on microstructure and mechanical properties of PH13-8Mo stainless steel[J]. Materials for Mechanical Engineering, 2014, 38(11): 72-75.

[1]	臧凯, 王守乾, 朱治愿. 固溶时效处理对21-4NWNb合金组织与性能的影响[J]. 金属热处理, 2024, 49(5): 88-93.
[2]	赵倩, 董福宇, 吴福川, 张悦, 徐欣. 固溶时效对Ti-5Al-3.5Fe-7Mo-4Cr合金组织与性能的影响[J]. 金属热处理, 2024, 49(5): 100-105.
[3]	刘子知, 孙福臻, 李晓旭, 李蕙宇, 张泉达, 穆雪松, 赵岩. 固溶时效处理对稀土铝合金力学性能及组织的影响[J]. 金属热处理, 2024, 49(5): 193-198.
[4]	何睿, 王杰, 尹慧, 翟瑞志, 向伟, 吕东莉, 尹耀吉. 热处理对锻态TC21钛合金组织及性能的影响[J]. 金属热处理, 2024, 49(4): 201-208.
[5]	刘阳, 亓海全, 秦翔智, 韩向楠, 李天然. 水热环境下Al-9.2Zn-2.4Mg-1.5Cu铝合金挤压板的固溶时效行为[J]. 金属热处理, 2024, 49(2): 166-171.
[6]	祁清文, 卜恒勇, 黎芩. 7000系铝合金固溶时效过程中微观组织变化的研究进展[J]. 金属热处理, 2024, 49(2): 244-251.
[7]	邸抑非, 李佳, 李勇, 赵荣达, 相珺, 伍复发. 固溶时效处理对AlMg5Si2Mn铝合金组织与性能的影响[J]. 金属热处理, 2024, 49(1): 148-153.
[8]	谭国寅. 固溶时效处理对2A14铝合金冲击性能的影响[J]. 金属热处理, 2023, 48(9): 126-128.
[9]	朱嘉欣, 孙有平, 陈少机, 谢尚恒, 周勇. 固溶时效处理对Mg-4Zn-0.3Zr合金显微组织及阻尼性能的影响[J]. 金属热处理, 2023, 48(7): 97-102.
[10]	谭国寅. 固溶时效处理对ZL108铝合金冲击性能的影响[J]. 金属热处理, 2023, 48(5): 291-293.
[11]	杨凯, 朱宏伟, 于利民, 郁瑞兴. 时效时间对PH13-8Mo不锈钢组织和力学性能的影响[J]. 金属热处理, 2023, 48(3): 100-103.
[12]	蒋小娟, 杨刚, 詹正阳, 程小伟, 董梦瑶, 邓国勇, 孙涛, 孙朝远. 热处理制度对Ti-1023钛合金微观组织及力学性能的影响[J]. 金属热处理, 2023, 48(12): 116-122.
[13]	吴晨, 马保飞, 赵耕岑, 李敏娜, 任军帅, 于奎. 延时淬火对航天紧固件用TC4钛合金组织和性能的影响[J]. 金属热处理, 2023, 48(12): 135-139.
[14]	郑超, 胡生双, 张兵宪, 张颖云, 颜家维, 欧阳德来. A286合金激光焊接接头的组织与高温持久性能[J]. 金属热处理, 2023, 48(10): 163-167.
[15]	高星, 张宁, 丁燕, 蒋波. 热处理时间对激光选区成形TC4钛合金组织及力学性能的影响[J]. 金属热处理, 2022, 47(9): 12-17.

PH13-8Mo不锈钢带状偏析及其在热处理中的演变

Strip segregation in PH13-8Mo stainless steel and its evolution during heat treatment

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价