人工关节材料纯钽的表面氧化工艺及硬度

doi:10.13251/j.issn.0254-6051.2024.11.044

金属热处理 ›› 2024, Vol. 49 ›› Issue (11): 284-289.DOI: 10.13251/j.issn.0254-6051.2024.11.044

人工关节材料纯钽的表面氧化工艺及硬度

杨光¹, 谢晓东², 罗勇², 许振陶², 孙孝礌², 祁阳³, 马贤¹

1.核工业理化工程研究院, 天津 300180;
2.中国矿业大学材料与物理学院, 江苏徐州 221116;
3.东北大学材料科学与工程学院, 辽宁沈阳 110819

收稿日期:2024-05-17 修回日期:2024-09-25 出版日期:2024-11-25 发布日期:2025-01-09
作者简介:杨光(1989—),男,副研究员,博士,主要研究方向为高性能铜合金、钛合金和钽合金的开发与应用,E-mail:yang7guang@163.com
基金资助:
中国博士后特别资助项目(2015T80598)

Surface oxygenation technology and hardness of pure tantalum used as artificial joints

Yang Guang¹, Xie Xiaodong², Luo Yong², Xu Zhentao², Sun Xiaolei², Qi Yang³, Ma Xian¹

1. Research Institute of Physics and Chemical Engineering of Nuclear Industry, Tianjin 300180, China;
2. School of Materials Science and Physics, China University of Mining and Technology, Xuzhou Jiangsu 221116, China;
3. School of Materials Science and Engineering, Northeastern University, Shenyang Liaoning 110819, China

Received:2024-05-17 Revised:2024-09-25 Online:2024-11-25 Published:2025-01-09

摘要/Abstract

摘要： 使用低压真空表面渗氧技术、扫描电镜、X射线衍射仪、X射线光电子能谱技术和纳米压痕技术等手段研究了不同工艺下人工关节材料纯钽的表面渗氧产物及硬度。结果表明,在500 ℃渗氧2 h、273 mL(通氧量,下同)的条件下可以在纯钽表面制备出物相为钽氧化合物Ta₄O、平均厚度约为3.6 μm的渗层。在550 ℃×2 h/273 mL、550 ℃×5 h/1.3 mL、550 ℃×10 h/0.013 mL以及650 ℃×3 h/0.013 mL条件下可以制备出δ-(Ta, O)化合物。通过调整渗氧温度、时间和通氧量可以实现δ-(Ta, O)化合物渗层厚度的改变。在550 ℃渗氧1 h、273 mL通氧量的条件下可制备出平均厚度约为60 μm的渗层,其物相为多价态钽的钽氧化合物;经渗氧处理后试样的硬度为(160.27±2.80) HV5,其最大纳米压痕硬度为7.92 GPa,显著地高于纯钽原始试样,该工艺可提高用于人工关节的钽基材料耐磨性,进而提高其使用寿命。

关键词: 纯钽, 表面渗氧, 钽氧化合物, 厚度, 硬度

Abstract: Surface oxygen infiltration products and hardness of the pure tantalum used as artificial joints under different processes were studied by means of low pressure vacuum surface oxygenation technology, scanning electron microscope (SEM), X-ray diffractometer (XRD), X-ray photoelectron spectroscopy (XPS) and nanoindentation technology. The results show that surface oxygen infiltrated layer with thickness of about 3.6 μm, which contains the phase of tantalum oxide Ta₄O, can be prepared under the condition of 500 ℃×2 h/273 mL(oxygen flow volume, the same below). The δ-(Ta, O) compounds can be prepared under the conditions of 550 ℃×2 h/273 mL, 550 ℃×5 h/1.3 mL, 550 ℃×10 h/0.013 mL and 650 ℃×3 h/0.013 mL. The thickness of surface oxygen infiltrated layer with δ-(Ta, O) compounds varies according to the parameters of oxygen infiltration temperature, time and oxygen flow volume. The surface oxygen infiltrated layer with the average thickness of nearly 60 μm is prepared under the condition of 550 ℃×1 h/273 mL, and the surface phase is tantalum oxides with polyvalent tantalum, the Vickers hardness and maximum nanoindentation hardness of the specimen are (160.27±2.80) HV5 and 7.92 GPa, respectively, which are significantly higher than those of the pure tantalum. This technology can be used to increase the abrasion resistance and lifespan of the Ta-based artificial joints.

Key words: pure tantalum, surface oxygenation, tantalum oxides, thickness, hardness

中图分类号:

TB31

杨光, 谢晓东, 罗勇, 许振陶, 孙孝礌, 祁阳, 马贤. 人工关节材料纯钽的表面氧化工艺及硬度[J]. 金属热处理, 2024, 49(11): 284-289.

Yang Guang, Xie Xiaodong, Luo Yong, Xu Zhentao, Sun Xiaolei, Qi Yang, Ma Xian. Surface oxygenation technology and hardness of pure tantalum used as artificial joints[J]. Heat Treatment of Metals, 2024, 49(11): 284-289.

参考文献

[1]蔡洪桢, 贺慧霞. 钽金属在临床应用中的研究进展[J]. 口腔颌面修复学杂志, 2017, 18(1): 46-50.
Cai Hongzhen, He Huixia. Clinical application of tantalum[J]. Chinese Journal of Prosthodontics, 2017, 18(1): 46-50.
[2]陈裕旭, 尹效华. 钽及其氧化物的生物学作用[J]. 预防医学情报杂志, 1999, 15(1): 14-16.
[3]姚子龙, 张余. 钽金属的生物学性能及在骨科临床的应用现状[J]. 广州医学院学报, 2013, 41(2): 135-138.
[4]李爱友, 徐韬, 车东航, 等. 钽粉支气管造影术的动物实验研究[J]. 中国医学影像技术, 1999, 15(4): 264-265.
Li Aiyou, Xu Tao, Che Donghang, et al. A study of tantalum powder in bronchoradiography on animals[J]. Chinese Journal of Medical Imaging Technology, 1999, 15(4): 264-265.
[5]李爱友, 徐韬, 车东航, 等. 钽粉胃造影术的动物实验研究[J]. 中国医学影像技术, 1999, 15(11): 905-906.
[6]张秀杰, 王志强. 多孔钽生物特性及在早期股骨头坏死中的应用[J]. 中国煤炭工业医学杂志, 2011, 14(8): 1249-1251.
[7]Moser K D. The manufacture and fabrication of tantalum[J]. JOM, 1999, 51: 29-31.
[8]Zhao Z, Hui P, Liu F, et al. Fabrication of TaC coating on tantalum by interstitial carburization[J]. Journal of Alloys and Compounds, 2019, 790: 189-196.
[9]曲铭浩, 胡跃辉, 冯景华, 等. 高介电氧化钽薄膜制备与介电性能分析[J]. 陶瓷学报, 2009, 30(2): 182-185.
Qu Minghao, Hu Yuehui, Feng Jinghua, et al. Preparation and dielectric properties analysis of high dielectric Ta₂O₅ thin films[J]. Journal of Ceramics, 2009, 30(2): 182-185.
[10]Geretovszky Z, Szörenyi T, Stoquert J P, et al. Correlation of compositional and structural changes during pulsed laser deposition of tantalum oxide films[J]. Thin Solid Films, 2004, 453: 245-250.
[11]Hino T, Nishida M, Araki T. Crystallization of tantalum oxide formed by PLD[J]. Surface and Coatings Technology, 2002, 149(1): 1-6.
[12]Lee S H, Kim J, Kim S J, et al. Hidden structural order in orthorhombic Ta₂O₅[J]. Physical Review Letters, 2013, 110(23): 235502.
[13]Pignolet A, Rao G M, Krupanidhi S. Rapid thermal processed thin films of reactively sputtered Ta₂O₅[J]. Thin Solid Films, 1995, 258(1/2): 230-235.
[14]Zhou M F, Fu Z W, Yang H J, et al. Pulsed laser deposition of tantalum oxide thin films[J]. Applied Surface Science, 1997, 108(3): 399-403.
[15]明帅强, 文庆涛, 高雅增, 等. 基于原子层沉积技术制备氧化钽薄膜及其特性研究[J]. 材料导报, 2021, 35(6): 6042-6047.
Ming Shuaiqiang, Wen Qingtao, Gao Yazeng, et al. Preparation of tantalum oxide thin films by atomic layer deposition technique and their property characterization[J]. Materials Reports, 2021, 35(6): 6042-6047.
[16]Chaze A, Coddet C. Influence of alloying elements on the dissolution of oxygen in the metallic phase during the oxidation of titanium alloys[J]. Journal of Materials Science, 1987, 22: 1206-1214.
[17]田茂财. Ti6Al4V合金表面渗氧强化及其生物摩擦学行为研究[D]. 徐州: 中国矿业大学, 2014: 1-77.
Tian Maocai. Oxidation of Ti6Al4V alloy and its biotribological properties[D]. Xuzhou: China University of Mining and Technology, 2014: 1-77.
[18]陈文文. Ti13Nb13Zr的热氧化层制备及其性能研究[D]. 徐州: 中国矿业大学, 2015: 1-89.
Chen Wenwen. Research on the preparation and the properties of Ti13Nb13Zr alloy's thermal oxide layer[D]. Xuzhou: China University of Mining and Technology, 2015: 1-89.
[19]Terao N. Structure des oxides de tantale[J]. Japanese Journal of Applied Physics, 1967, 6(1): 21-34.

人工关节材料纯钽的表面氧化工艺及硬度

Surface oxygenation technology and hardness of pure tantalum used as artificial joints

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	赵勇桃, 吴银虎, 鲁海涛, 王瑞, 雷丙旺. 不同等温温度下P92钢的组织演变[J]. 金属热处理, 2024, 49(9): 47-50.
[2]	孙陶安, 吴正义, 周继顺, 肖丙政, 王海川, 范鼎东, 邓爱军. Mo含量对高碳钢组织和耐磨性的影响[J]. 金属热处理, 2024, 49(9): 64-71.
[3]	路峰, 李琦, 孙雪娇, 邱国兴. 18CrNiMo7-6风电齿轮钢的动态CCT曲线[J]. 金属热处理, 2024, 49(9): 86-90.
[4]	陈琳, 李子岩, 白小波, 李双喜. 小模数地铁联轴器的离子渗氮工艺[J]. 金属热处理, 2024, 49(9): 209-215.
[5]	汲庆涛, 孙有政, 杨慧, 赵忠超, 史晓明. 时效时间对7175铝合金组织和力学性能的影响[J]. 金属热处理, 2024, 49(9): 242-246.
[6]	刘海量, 徐自立, 刘洋, 胡嘉彬. 45钢表面双辉等离子渗铝处理[J]. 金属热处理, 2024, 49(9): 280-283.
[7]	刘运娜, 孙笠灿, 戴观文, 刘献达, 宋仁伯, 张朝磊. 冷却速率和Nb微合金化对25MnV非调质钢组织和硬度的影响[J]. 金属热处理, 2024, 49(8): 31-35.
[8]	刘静, 赵科, 王丽阁. 退火对Co_xFe₃₅Mn₂₅Cr₁₅Ni₁₀Ti₅高熵合金微观组织及硬度的影响[J]. 金属热处理, 2024, 49(8): 94-101.
[9]	孙昭琦, 李涛, 韩强, 张行刚, 白岩松, 高志敏. 淬火工艺对28MnCrMoRE油井管钢显微组织及硬度的影响[J]. 金属热处理, 2024, 49(8): 160-164.
[10]	刘梓峰, 赵旭亮, 罗皓. 淬火温度对4Cr4Mo3W2V1模具钢组织与硬度的影响[J]. 金属热处理, 2024, 49(8): 170-173.
[11]	李峰. 钛改性离子渗氮处理对沉淀硬化钢性能的影响[J]. 金属热处理, 2024, 49(8): 183-188.
[12]	丁红珍, 李航, 邱万奇. 变电场辅助低温渗硼制备单相Fe₂B渗层[J]. 金属热处理, 2024, 49(8): 195-199.
[13]	王岗, 杨舜明, 匡光辉. 3105铝合金铸锭的均匀化[J]. 金属热处理, 2024, 49(8): 200-203.
[14]	杜茂华, 张振新, 毕贵军, 曹立超. 激光熔覆420不锈钢的热流耦合数值模拟与试验验证[J]. 金属热处理, 2024, 49(8): 211-219.
[15]	陈作宁, 师仲然, 胡骞, 展之德, 罗小兵. 390 MPa级抗碰撞船体钢的奥氏体连续冷却转变[J]. 金属热处理, 2024, 49(7): 146-151.