Mn含量对超低碳贝氏体钢连续冷却转变规律的影响

doi:10.13251/j.issn.0254-6051.2024.12.026

金属热处理 ›› 2024, Vol. 49 ›› Issue (12): 157-162.DOI: 10.13251/j.issn.0254-6051.2024.12.026

Mn含量对超低碳贝氏体钢连续冷却转变规律的影响

梅涛^1,2, 刘静¹, 柴希阳²

1.武汉科技大学省部共建耐火材料与冶金国家重点实验室, 湖北武汉 430081;
2.钢铁研究总院有限公司工程用钢研究院, 北京 100081

收稿日期:2024-06-03 修回日期:2024-10-15 出版日期:2024-12-25 发布日期:2025-02-05
通讯作者: 刘静,教授,博士,E-mail:liujing@wust.edu.cn
作者简介:梅涛(1998—),男,硕士研究生,主要研究方向为船用超低碳贝氏体钢的强韧性,E-mail:mtwust2017@163.com。

Effect of Mn content on continuous cooling transformation of ultra-low carbon bainitic steel

Mei Tao^1,2, Liu Jing¹, Chai Xiyang²

1. State Key Laboratory of Refractory Materials and Metallurgy, Wuhan University of Science and Technology, Wuhan Hubei 430081, China;
2. Research Institute of Structural Steels, Central Iron and Steel Co., Ltd., Beijing 100081, China

Received:2024-06-03 Revised:2024-10-15 Online:2024-12-25 Published:2025-02-05

摘要/Abstract

摘要： 使用热膨胀仪测定了Mn含量分别为1.5%、1.8%和2.1%的3种超低碳贝氏体钢相变点,结合光学显微镜(OM)、扫描电镜(SEM)观察以及维氏硬度测量,绘制了3种试验钢的连续冷却转变(CCT)曲线,分析了Mn含量变化对相变点、CCT曲线、组织以及硬度的影响。结果表明,Mn含量提升引起的Mn当量变化会影响贝氏体转变温度,此外Mn含量的提升会使试验钢Ac₃呈现下降的趋势,且硬度也得到提升。

关键词: 超低碳贝氏体钢, Mn含量, CCT曲线, 粒状贝氏体, 板条状贝氏体

Abstract: Phase transition points of three ultra-low carbon bainitic steels with Mn contents of 1.5%, 1.8%, and 2.1%, respectively, were determined using a thermal expansion meter, and the continuous cooling transformation(CCT) curves of the three tested steels were plotted in conjunction with optical microscopy(OM) and scanning electron microscopy(SEM) observation and Vickers hardness measurements. The effects of Mn content on phase transformation points, CCT curves, microstructure and hardness were analyzed. The results show that the change of Mn equivalent caused by the increase of Mn content affects the bainite transformation temperature. In addition, the increase of Mn content makes the Ac₃ of the tested steel show a downward trend, and the hardness is also improved.

Key words: ultra-low carbon bainitic steel, Mn content, CCT curves, granular bainite, lath bainite

中图分类号:

TG142

梅涛, 刘静, 柴希阳. Mn含量对超低碳贝氏体钢连续冷却转变规律的影响[J]. 金属热处理, 2024, 49(12): 157-162.

Mei Tao, Liu Jing, Chai Xiyang. Effect of Mn content on continuous cooling transformation of ultra-low carbon bainitic steel[J]. Heat Treatment of Metals, 2024, 49(12): 157-162.

参考文献

[1]李纪委, 刘庆锁. 超低碳贝氏体钢的研究现状[J]. 天津理工大学学报, 2008(1): 56-59.
Li Jiwei, Liu Qingsuo. Research status on ULCB steel[J]. Journal of Tianjin University of Technology, 2008(1): 56-59.
[2]田亚强, 田耕, 郑小平, 等. 低碳高强贝氏体钢的研究现状[J]. 钢铁研究学报, 2018, 30(7): 505-514.
Tian Yaqiang, Tian Geng, Zheng Xiaoping, et al. Research status of low carbon high strength bainitic steel[J]. Journal of Iron and Steel Research, 2018, 30(7): 505-514.
[3]胡张薇, 徐光, 王力, 等. C-Mn-Si-Mo系低碳贝氏体钢连续冷却转变曲线[J]. 金属热处理, 2014, 39(9): 111-113.
Hu Zhangwei, Xu Guang, Wang Li, et al. Continuous cooling transformation curves of C-Mn-Si-Mo series low carbon bainite steel[J]. Heat Treatment of Metals, 2014, 39(9): 111-113.
[4]Garcia C I, Deardo A J. Ultra-low carbon bainitic steels for heavy plate applications[R]. David Taylor Research Center, U. S. Navy, 1990.
[5]缪鹏飞, 童彦刚, 郭彦兵. 超低碳贝氏体钢中合金元素的作用及其对焊接性的影响[J]. 热加工工艺, 2010, 39(20): 29-32, 35.
Miao Pengfei, Tong Yangang, Guo Yanbing, et al. Effect of alloying elements on ultra-low-carbon bainite steel and its influence on weldability[J]. Hot Working Technology, 2010, 39(20): 29-32, 35.
[6]赵路遇. 超低碳贝氏体钢及其在舰船上的应用[J]. 材料开发与应用, 2006, 21(2): 34-37, 43.
Zhao Luyu. Ultra-low carbon bainite steel and its application in naval-ship[J]. Development and Application of Materials, 2006, 21(2): 34-37, 43.
[7]Lis A K, Lis J, Jeziorski L. Advanced ultra-low carbon bainitic steels with high toughness[J]. Journal of Materials Processing Technology, 1997, 64(1-3): 255-266.
[8]史远, 戴观文, 安治国, 等. 高强贝氏体非调质钢的奥氏体连续冷却相变[J]. 金属热处理, 2019, 44(2): 25-29.
Shi Yuan, Dai Guanwen, An Zhiguo, et al. Continuous cooling transformation of austenite for high strength bainitic non-quenched and tempered steel[J]. Heat Treatment of Metals, 2019, 44(2): 25-29.
[9]王建泽, 康永林, 杨善武, 等. ULCB钢相变产物粒状与板条状贝氏体组织性能研究[J]. 材料工程, 2006(S1): 252-254, 258.
Wang Jianze, Kang Yonglin, Yang Shanwu, et al. Study on microstructure and properties of granular bainite and bainite ferrite of ULCB steel transformation production[J]. Journal of Materials Engineering, 2006(S1): 252-254, 258.
[10]蒋波, 霍朝霞, 周乐育, 等. 奥氏体变形和Mn对42CrMo钢连续冷却相变组织的影响[J]. 材料热处理学报, 2014, 35(8): 119-124.
Jiang Bo, Huo Chaoxia, Zhou Leyu, et al. Effect of austenite deformation and manganese content on microstructure of continuous cooling transformation of 42CrMo steel[J]. Transactions of Materials and Heat Treatment, 2014, 35(8): 119-124.
[11]龙晓燕, 张福成, 康杰, 等. Mn对无碳化物贝氏体钢组织和性能的影响[J]. 金属热处理, 2017, 42(11): 29-35.
Long Xiaoyan, Zhang Fucheng, Kang Jie, et al. Influence of Mn on microstructure and mechanical properties of carbide-free bainitic steel[J]. Heat Treatment of Metals, 2017, 42(11): 29-35.
[12]叶建军. 合金元素对ULCB钢组织和机械性能的影响[J]. 宽厚板, 2004(6): 40-45.
Ye Jianjun. Effect of alloying elements on structure and mechanical properties of ULCB steel[J]. Wide and Heavy Plate, 2004(6): 40-45.
[13]王建泽, 康永林, 杨善武, 等. ULCB钢相变产物粒状与板条状贝氏体组织性能研究[J]. 材料工程, 2006(S1): 252-254, 258.Wang Jianze, Kang Yonglin, Yang Shanwu, et al. Study on microstructure and properties of granular bainite and bainite ferrite of ULCB steel transformation production[J]. Journal of Materials Engineering, 2006(S1): 252-254, 258.
[14]黎先浩, 康永林, 陈林恒, 等. CSP生产600 MPa级低碳贝氏体钢的相变[J]. 北京科技大学学报, 2009, 31(6): 701-707.
Li Xianhao, Kang Yonglin, Chen Linheng, et al. Continuous cooling transformation of 600 MPa grade low carbon bainite steel produced by CSP process[J]. Journal of University of Science and Technology Beijing, 2009, 31(6): 701-707.
[15]周千学, 黄海娥, 杨志婷. 3.5Ni低温钢中Mn元素的强韧性作用研究[J]. 武汉科技大学学报, 2013, 36(5): 379-382.
Zhou Qianxue, Huang Haie, Yang Zhiting. Toughening effect of Mn in 3.5Ni low temperature steel[J]. Journal of Wuhan University of Science and Technology, 2013, 36(5): 379-382.
[16]桂晓露, 刘蓉, 高古辉, 等. Cr元素对贝氏体钢连续转变规律的影响[J]. 材料热处理学报, 2016, 37(10): 154-158.
Gui Xiaolu, Liu Rong, Gao Guhui, et al. Effect of Cr on continuous cooling transformation characteristic of bainitic steels[J]. Transactions of Materials and Heat Treatment, 2016, 37(10): 154-158.

Mn含量对超低碳贝氏体钢连续冷却转变规律的影响

Effect of Mn content on continuous cooling transformation of ultra-low carbon bainitic steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	高兴成, 吴博雅, 吴晓春. 4Cr5Mo2V热作模具钢的CCT曲线及碳化物沿晶析出温度测定[J]. 金属热处理, 2024, 49(9): 72-79.
[2]	袁静, 陈飞达, 钟海清, 唐小勇, 朱映玉, 冷烨旻, 肖虎, 田世伟. XGTC300L搪瓷钢的连续冷却转变行为与析出规律[J]. 金属热处理, 2024, 49(9): 80-85.
[3]	周蕾, 王莹, 张永健, 赵晓丽, 惠卫军. V+Ti微合金化Mn-Cr系贝氏体型非调质钢的氢脆敏感性[J]. 金属热处理, 2024, 49(7): 106-112.
[4]	黄剑涛, 张明赫, 冯运莉, 尹绍江, 陈春生, 王厚昕. V-Nb微合金化Q420B大规格角钢的连续冷却转变规律[J]. 金属热处理, 2024, 49(7): 121-127.
[5]	陈作宁, 师仲然, 胡骞, 展之德, 罗小兵. 390 MPa级抗碰撞船体钢的奥氏体连续冷却转变[J]. 金属热处理, 2024, 49(7): 146-151.
[6]	董丽丽, 崔成波, 袁晓鸣, 刘泽田. BTP500钢板过冷奥氏体连续冷却转变行为[J]. 金属热处理, 2024, 49(7): 157-160.
[7]	刘阳, 高茗, 马莉, 胡祯, 孙中梅, 张士震. 低成本无钒热轧钢筋HRB400E的生产工艺优化[J]. 金属热处理, 2024, 49(7): 294-300.
[8]	刘干, 孔祥磊, 黄明浩, 王杨, 张英慧. 冷却速率对超高强度X90M管线钢相变行为的影响[J]. 金属热处理, 2024, 49(5): 162-167.
[9]	黄东, 蒋义然. S355低合金结构钢的动态连续冷却转变曲线及力学性能[J]. 金属热处理, 2024, 49(4): 38-41.
[10]	童炀, 张婧, 辛文彬, 罗果萍, 彭军, 侯蹬云. Nb含量对V-Ti-N工程结构用钢连续冷却转变规律及组织性能的影响[J]. 金属热处理, 2024, 49(3): 236-243.
[11]	曹佳丽, 靳红泽, 李康立, 徐亚鹏, 赵强, 王翠萍, 李梦楠. 水电用Q690CFD低合金高强钢SH-CCT曲线测定与分析[J]. 金属热处理, 2024, 49(2): 60-65.
[12]	高鑫, 宁静, 苏杰, 高齐, 姜庆伟. 中碳Cr-Mn-Si低合金钢的过冷奥氏体连续冷却转变曲线[J]. 金属热处理, 2024, 49(12): 142-147.
[13]	杨维宇, 魏晓东, 白雅琼, 张晓峰, 郎荣彪. 微量稀土Ce对DX51D+Z低碳钢连续冷却转变曲线的影响[J]. 金属热处理, 2024, 49(10): 234-238.
[14]	陈玉波, 王培杰, 原海瑞, 李振江. 正火温度对G18CrMo2-6铸钢微观组织及力学性能的影响[J]. 金属热处理, 2024, 49(1): 137-141.
[15]	鄢文泽, 闫文青, 林轩艺, 王红鸿. 铌微合金化对低合金高强钢模拟焊接热影响区粒状贝氏体相变及SH-CCT曲线的影响[J]. 金属热处理, 2023, 48(9): 150-156.