Effect of tempering temperature on microstructure and properties of  particle reinforced low-alloyed wear resistant steel

doi:10.13251/j.issn.0254-6051.2022.03.001

Abstract

Abstract: Microstructure, mechanical properties and wear resistance of particle reinforced low-alloyed wear resistant steel tempered at different temperatures were studied. The results show that a large number of micron-scale and nanoscale TiC particles are uniformly dispersed in the rolled particle reinforced low-alloyed wear resistant steel. With the tempering temperature increasing, more ε-carbides are precipitated in the matrix, the yield strength of the tested steel overall increases first and then decreases, the tensile strength, hardness and impact absorbed energy gradually decrease, while the elongation gradually increases. The tested steel shows the best comprehensive mechanical properties and three-body abrasive wear properties when tempered at 200 ℃.

Key words: low-alloyed wear resistant steel, TiC particles, tempering treatment, abrasive wear, microstructure and properties

CLC Number:

TG142.1

Huang Long, Deng Xiangtao, Wang Zhaodong. Effect of tempering temperature on microstructure and properties of particle reinforced low-alloyed wear resistant steel[J]. Heat Treatment of Metals, 2022, 47(3): 1-6.

References

[1]谢友柏. 摩擦学科学及工程应用现状与发展战略研究[M]. 北京: 高等教育出版社, 2009.
[2]魏世忠, 徐流杰. 钢铁耐磨材料研究进展[J]. 金属学报, 2020, 54(4): 523-538.
Wei Shizhong, Xu Liujie. Review on research progress of steel and iron wear-resistant materials[J]. Acta Metallurgica Sinica, 2020, 54(4): 523-538.
[3]吴昊, 邓想涛, 李成儒, 等. 耐磨钢NM400冷弯开裂分析[J]. 金属热处理, 2021, 46(9): 262-267.
Wu Hao, Deng Xiangtao, Li Chengru, et al. Analysis on cold bending fracture of wear-resistant steel NM400[J]. Heat Treatment of Metals, 2021, 46(9): 262-267.
[4]李灿明. 淬火工艺对耐磨钢NM400组织性能的影响[J]. 金属热处理, 2021, 46(6): 69-73.
Li Canming. Effect of quenching on microstructure and properties of wear-resistant steel NM400[J]. Heat Treatment of Metals, 2021, 46(6): 69-73.
[5]姜金星, 董俊媛, 王慧慧, 等. 回火工艺对厚规格NM450耐磨钢组织和硬度的影响[J]. 金属热处理, 2020, 45(1): 117-121.
Jiang Jinxing, Dong Junyuan, Wang Huihui, et al. Effect of tempering on microstructure and hardness of thick gauge NM450 wear-resistant steel slab[J]. Heat Treatment of Metals, 2020, 45(1): 117-121.
[6]邓想涛. 低合金耐磨钢组织性能控制及磨损机理研究[D]. 沈阳: 东北大学, 2014.
[7]Deng Xiangtao, Wang Zhaodong, Han Yi, et al. Microstructure and abrasive wear behavior of medium carbon low alloy martensitic abrasion resistant steel[J]. Journal of Iron and Steel Research (International), 2014, 21(1): 98-103.
[8]Xu Liujie, Wei Shizhong, Xiao Fangnao, et al. Effects of carbides on abrasive wear properties and failure behaviors of high speed steels with different alloy element content[J]. Wear, 2017, 376-377: 968-974.
[9]Wei Shizhong, Zhu Jinhua, Xu Liujie, Effects of vanadium and carbon on microstructures and abrasive wear resistance of high speed steel[J]. Tribology International, 2005, 39(7): 641-648.
[10]Huang Long, Deng Xiangtao, Jia Ye, et al. Effects of using (Ti, Mo)C particles to reduce the three-body abrasive wear of a low alloy steel[J]. Wear, 2018, 410-411: 119-126.
[11]Huang Long, Deng Xiangtao, Li Chengru, et al. Effect of TiC particles on three-body abrasive wear behavior of low alloy abrasion-resistant steel[J]. Wear, 2019, 434-435: 202971.
[12]Huang Long, Deng Xiangtao, Wang Qi, et al. Solidification and sliding wear behavior of low-alloy abrasion-resistant steel reinforced with TiC particles[J]. Wear, 2020, 458-459: 203444.
[13]Huang Long, Deng Xiangtao, Wang Qi, et al. Microstructure, mechanical properties and wear resistance of low alloy abrasion resistant martensitic steel reinforced with TiC particles[J]. ISIJ International, 2020, 60(11): 2586-2595.
[14]王日清, 邓想涛, 王昭东, 等. 含钛低合金超高强耐磨钢的连续冷却相变行为[J]. 钢铁研究学报, 2011, 23(5): 55-58, 62.
Wang Riqing, Deng Xiangtao, Wang Zhaodong, et al. Continuous cooling transformation behavior of Ti-containing low-alloy ultra-high strength abrasion-resistant steel[J]. Journal of Iron and Steel Research, 2011, 23(5): 55-58, 62.
[15]Dong Chen, Wu Huibin, Wang Xiangtao. Effect of tempering temperatures on microstructures and properties of 0.28C-0.22Ti wear-resistant steel[J]. Materials Science and Technology, 2018, 34(1): 86-94.
[16]温长飞, 肖爱达, 刘旭辉, 等. 回火温度对低合金超高强钢Q1300组织与性能的影响[J]. 金属热处理, 2019, 44(2): 172-177.
Wen Changfei, Xiao Aida, Liu Xuhui, et al. Effect of tempering temperature on microstructure and mechanical properties of low alloy ultra-high strength steel Q1300[J]. Heat Treatment of Metals, 2019, 44(2): 172-177.

Effect of tempering temperature on microstructure and properties of particle reinforced low-alloyed wear resistant steel

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	Gao Yaping, Shi Zhongran, Jia Juan, Luo Xiaobing, Song Xinli. Effect of heat treatment process on microstructure and abrasive wear properties of dredging engineering ship steel [J]. Heat Treatment of Metals, 2022, 47(1): 32-37.
[2]	Huang Juan, Huang Yuanchun, Shen Zhenyu, Li Xiangyue, Zeng Yu, Yang Gengchen. Effect of finish rolling temperature and annealing temperature on microstructure and properties of 5052 aluminum alloy sheet [J]. Heat Treatment of Metals, 2021, 46(9): 79-84.
[3]	Li Minna, Ma Baofei, Guo Jinming, Wu Chen, Xiao Songtao. Heat treatment of TB8 titanium alloy with high strength and toughness [J]. Heat Treatment of Metals, 2021, 46(9): 116-119.
[4]	Wu Hao, Deng Xiangtao, Li Chengru, Sui Yi, Zhang Tao, Ji Wenbo, Wang Zhaodong. Analysis on cold bending fracture of wear-resistant steel NM400 [J]. Heat Treatment of Metals, 2021, 46(9): 262-267.
[5]	Wang Zili, Chen Rongfa, Zheng Zhiwei, He Yulong, Shi Minjie, Wang Kai, Zhou Xiaojin. Microstructure and wear resistance of oxynitriding layer on piston rod surface of 42CrMo steel [J]. Heat Treatment of Metals, 2021, 46(8): 225-229.
[6]	Hua Siming, Zhang Pingze, Liu Zili. Aging process, microstructure and properties of CuCr1 alloy contact wire [J]. Heat Treatment of Metals, 2021, 46(5): 143-149.
[7]	Wang Sicheng, Zhou Dan, Chai Xiyang, Tong Shi, Yang Yang, Wang Tianqi. Effect of controlled rolling and controlled cooling process on microstructure and properties of 440 MPa grade hull steel [J]. Heat Treatment of Metals, 2021, 46(4): 138-142.
[8]	Chen Zhuo, Wang Chengsi, Jin Bin, Liu Jingbao, Hao Lei, Kuang Shuang, Wang Jinrong. Multiple regulation on mechanical properties of 980 MPa cold-rolled multi-phase steel [J]. Heat Treatment of Metals, 2021, 46(4): 157-160.
[9]	Shi Xiaoxia, Ren Huiping, Li Xiao, Wang Chao, Gong Xin. Study on boundary of efficient quenching and tempering process of 26CrMoVNbRE steel [J]. Heat Treatment of Metals, 2021, 46(3): 39-45.
[10]	Chen Yiwu, Wu Xinxiang, Zhou Lihua, Fu Tianzuo, Zhao Jing, Li Sheng. Microstructure and properties of laser clad layer on high strength stainless steel [J]. Heat Treatment of Metals, 2021, 46(10): 232-236.
[11]	Wang Keqiang, Liu Rendong, Guo Jinyu, Fu Wei, Huang Qiuju, Sun Rongsheng. Development of cold-rolled 800 MPa grade high strength low alloy steel for automobile [J]. Heat Treatment of Metals, 2021, 46(1): 120-124.
[12]	Li Zhihong, Ding Hao, Zhu Shigen. Effect of electrical contact strengthening on microstructure and properties of Ni/Cu composite coatings [J]. Heat Treatment of Metals, 2020, 45(8): 228-232.
[13]	Yan Lei, Li Xuming, Li Kaifeng, Ma Fengchun. Effect of tempering process on microstructure and properties of 1Cr12Ni3MoVN steel [J]. HTM, 2020, 45(3): 196-199.
[14]	Liu Luojin, Sun Xinjun, Liang Xiaokai, Ye Xiaoyu. Wear resistance of TiC particle reinforced low alloy ferritic wear-resistant steel [J]. HTM, 2020, 45(2): 56-60.
[15]	Yang Yuehui, Yuan Shaoqiang, Guo Jifu, Han Huijie, Zhang Yanlong. Effect of tempering temperature on microstructure and properties of composite steel plate for saw blade [J]. HTM, 2020, 45(2): 214-217.