| [1] |
Nie Xiaolong, Gao Jiaqiang, Meng Kairen, Wang Junyi, Liu Xinkuan.
Fracture failure analysis of 60Si2Mn spring steel
[J]. Heat Treatment of Metals, 2021, 46(8): 246-249.
|
| [2] |
Shen Kang, Cai Wenhe, Du Shuangming, Dong Shuqing, Gao Dawei, Bai Yin.
Effect of shot peening on high-temperature steam oxidation behavior of martensitic heat-resistant steel
[J]. Heat Treatment of Metals, 2021, 46(2): 66-73.
|
| [3] |
Wang Jian, Meng Haojie, Li Peng, Li Guoping, Li Jun, Liu Jie, Han Peide.
Effect of shot peening and hydrochloric acid pickling on oxide layer microstructure of 2205 duplex stainless steel hot-rolled sheet
[J]. Heat Treatment of Metals, 2021, 46(2): 74-80.
|
| [4] |
Yang Yang, Che Yongping, Hai Xianü, Li Yang, Wang Ye.
Shot peening process test for spur gear parts
[J]. Heat Treatment of Metals, 2021, 46(2): 81-86.
|
| [5] |
Wang Xin, Yang Qing, Yu Peng, Ma Shicheng.
Shot peening process of directionally solidified DZ125 alloy
[J]. Heat Treatment of Metals, 2021, 46(1): 149-153.
|
| [6] |
Lu Hui, Chen Yinli, Wei He, Liu Zesheng.
Retained austenite and carbide in 55SiCr spring steel
[J]. Heat Treatment of Metals, 2020, 45(5): 103-109.
|
| [7] |
Wang Chao, Zhang Hai, Li Dongfei, Yun Hao, Xu Wensu, Zhao Wu.
Effect of microparticle shot peening on residual stress field of target
[J]. Heat Treatment of Metals, 2020, 45(5): 192-198.
|
| [8] |
Kang Xia, Yin Guangqiang, Zhao Guiping.
Influence of shot peening on fatigue property of maraging ultra-high strength steel
[J]. HTM, 2020, 45(2): 253-256.
|
| [9] |
Zhu Min, Zhu Wanquan, Shuai Linfei, Ma Guoqiang, Wu Guilin.
Softening and hardening of 18CrNiMo7-6 steel during surface nanocrystallization treatment
[J]. HTM, 2019, 44(1): 152-156.
|
| [10] |
Lü Wenbo, Zhang Hai, Zhang Xiaomin, Han Junhao, Song Xiaoqing, Zhao Wu.
Numerical simulation on influencing factors of micropartical shot peening
[J]. HTM, 2019, 44(1): 235-240.
|
| [11] |
Chen Caihong1, Wang Xin2,Zhou Jian1, Yin Liqing1.
Residual stress porfile and thermal-relaxtion of shot-peened titanium alloy
[J]. HTM, 2016, 41(6): 55-58.
|
| [12] |
Yin Xiaoning1, Fu Xuesong1, Chen Guoqing1, Zhou Wenlong 1, Gai Pengtao2, Li Zhiqiang2.
Effect of wet shot peening on surface appearance and fatigue property of Ti-6Al-4V alloy
[J]. HTM, 2016, 41(3): 48-53.
|
| [13] |
Yang Shiting， Xing Yongming, Lang Fengchao, Li Jijun, Jiang Aifeng.
Friction and wear properties of 316L stainless steel after shot peening
[J]. HTM, 2016, 41(11): 35-39.
|
| [14] |
Ma Ming，Tian Long, He Qiang.
Effect of hole strengthening treatment on fatigue property of magnesium alloy parts with hole
[J]. HTM, 2014, 39(6): 106-108.
|
| [15] |
Yu Yingyan, Zhou Jie, Li Mengyao, Gao Lin.
Compound surface strengthening of hot working dies by shot peening and multi-element nitrocarburizing
[J]. HTM, 2014, 39(2): 81-84.
|
